Electronics Forum: mpm y-axis shuttle (Page 1 of 3)

Camera not parked error on mpm ap 25.

Electronics Forum | Mon Jun 12 23:52:58 EDT 2017 | aemery

Don, either you have a faulty park sensor or much more likely the vision gantry Y axis is not reaching the sensor. Possible issues, one of the two VY drivers cards is failing; one of the VY forcer motors (air bearings) is failing; to much air leakin

MPM AP25 Print Repeatability Problem

Electronics Forum | Fri Sep 22 13:03:26 EDT 2006 | daxman

I ran the vision test...here is what I got. Camera System: Completed Repeatability VX mean = -3.177942 Standard Deviation = .000059 VY mean = -12.114077 Standard Deviation = .000065 Vision System: Completed Repeatabi

Re: Modification of Fuji machine

Electronics Forum | Thu Oct 29 01:21:38 EST 1998 | Erhard

Thinking about that 180� turn unit again: You wouldn't require the the y-movement. The fixed side gets turned over to the other side anyways. | My suggestion would also be to leave the Fuji direction the way it is. (It's more standard anyways?) and

VY Software limit MPM UP2000

Electronics Forum | Wed Aug 05 14:20:21 EDT 2009 | jorge_quijano

Hello there, I'm having some problems w/MPM up2000, Vision Y axis software limit error, when I tried to create a new program, appears the "Value out of range for VY BSS POS, spec 0.00 min -26.5, read 8.45" message. Any idea of how to correct this pro

MPM UP3000 Question

Electronics Forum | Fri Aug 11 11:18:20 EDT 2006 | chrisgriffin

I got a 3000 that is acting crazy. After a print, the board is unclamped and the Z-axis lowers. It continues to lower until it trips the limit switch. It is suppposed to move in the Y-axis to line up with the tracks while lowering in the Z-axis.

MPM SPM Supplies

Electronics Forum | Fri Feb 23 08:53:52 EST 2007 | russ

Ours does not have a vacuum option so that may be it, the machine came with an assortment of standoffs and support plates as well. it is not drilled out in a grid but does have the center tapped which I assume is for the vacuum tooling. Ours has a

Need drawing for MPM Speedline Accuflex Printer

Electronics Forum | Mon Oct 05 13:15:05 EDT 2020 | proceng1

I am trying to replace the anti-backlash nuts for the moveable rail on my ACCUFLEX Printer. I have parts diagrams, but none show the Y-axis width lead screw assembly. I can't figure out how to disassemble the screws to get the nuts out. Does som

MPM UP3000 Question

Electronics Forum | Mon Aug 14 11:30:25 EDT 2006 | SWAG

We had centernest to I/O track alignment problems that were not predictable on 3000. Z-axis height seemed good with relation to I/O tracks but y was misaligned. Ended up replacing y-axis stepper and trouble went away. Also have had trouble with z-

Re: Modification of Fuji machine

Electronics Forum | Wed Oct 28 02:03:18 EST 1998 | Erhard Hofmann

| | | We currently using the Panasert SMT machine where PCB flow | | | direction were from right to left, & we are planning to move | | | in the FUJI -CP3 & CP4-2 in line where standard PCB | | | flow direction were left to right. | | | Any comment o

Screen Printers

Electronics Forum | Tue Dec 03 07:57:27 EST 2002 | pjc

Price of DEK 248 and MPM UP100 are about the same, $22-36K range. MPM UP100 has programmable squeegee pressure. Precise, repeatable results with less operator involvement. Pressure parameters saved in board program file. DEK 248 has manual microm

  1 2 3 Next

mpm y-axis shuttle searches for Companies, Equipment, Machines, Suppliers & Information