Electronics Forum | Mon Jul 01 14:46:47 EDT 2019 | assuredtech
It's been awhile but yes, if you do not allow the machine to optimize your program and your placing sequence is such that the tallest component is perhaps the 1st or last placement so it doesn't bump into other components, next is you may look into a
Electronics Forum | Sat Aug 03 01:40:24 EDT 2019 | sarason
I own a metcal for the high precision work 1500$ in 1992 tips $60 in 1992 and have only used one tip in all that time, have horses holves for large pin devices, precision points for 0402 and a largest tip for service work. Also have Hakkos for bulk
Electronics Forum | Thu Jul 18 17:06:19 EDT 2019 | spoiltforchoice
I can't imagine anything more tedious than continuously swapping feeders during a build (unless your panels are 10mins++) and the very suggestion this was a good idea when were were looking at MY's was comical to me. You should expect all TP series
Electronics Forum | Thu Jul 25 16:20:59 EDT 2019 | bobpan
Top red led is on or off depending on version of tep board. The green leds light when the transport sensor that it communitcates with is seeing a board over it. Tep controller init failure can be one of the following. 1. Check reseat tep card and
Electronics Forum | Thu Jan 09 20:52:02 EST 2020 | Mike Konrad
If the world was a perfect place, I would recommend preventing solder balls in the first place. While low amounts of solder balls are common, a high volume of solder balls are problematic to a cleaning machine (batch or inline). Solder balls may beco
Electronics Forum | Wed Mar 25 11:16:35 EDT 2020 | richardcargill
Currently working through a myriad of air leaks on an old MPM Ap -b and have a question that hopefully one of you fine people may know the answer to. The camera vx and vy use linear rail motors. As far as I can tell, there are nozzles between the sur
Electronics Forum | Wed Jun 24 10:17:50 EDT 2020 | kylehunter
> Hi. Guessing that you are operational by now? If > not, consider to use BGA definition and use the > editor to define where the bottom side pads are > or are not. Just our 2 bits input. The Assembleon > X / Yamaha units are quite
Electronics Forum | Wed Dec 23 20:06:26 EST 2020 | marcelorotofrance
Hi, I'm using a "ye olde" Quad 4c Mk2 built in 1995 for eight years. During that period I had to change 3 HDD (now it runs a compact flash with and free DOS), 3 Z-rod bellows,3 laser heads, some monitors, nozzles and misc parts. Despite that it has t
Electronics Forum | Tue Feb 16 16:57:44 EST 2021 | spoiltforchoice
But that only applies fully if you have the nozzles inline head to match, fast turret heads prefer to hammer a single lane, at least that would be my understanding given I don't have one :(. More active reels = more to track, that may matter to some.
Electronics Forum | Wed Feb 24 10:57:52 EST 2021 | spoiltforchoice
And then they make a new machine, and start the software all over again, or change the hardware so much the older model doesn't get any of the software tweaks on the new one even if they are supposedly the same model.... Neoden bigger machines shoul
SCANSMT is local stocking dealer who major in SAMSUNG,PANASONIC,YAMAHA,JUKI,FUJI mounter and MIRTEC,KOHYOUNG,PARMI,PEMTRON,CYBEROPTICS AOI&SPI,MPM,SJ,ESE Printers.HELLER,TSM Reflows are always have invertonries.welcome to visit us
Training Provider / Manufacturer / Equipment Dealer / Broker / Auctions / Consultant / Service Provider
Floor 1,D Building,B area,Dongsheng Techwin Park,Bao'an District
Shenzhen, 30 China
Phone: 008618566662725