Electronics Forum: sets (Page 246 of 458)

ive solder profiles

Electronics Forum | Tue Aug 12 13:40:08 EDT 2008 | ck_the_flip

GR@ICS: Are you drag soldering or point-to-point soldering? Keep in mind. Drag soldering mimics wave soldering. Molten solder is contacting and dragging across the solder mask. Keep in mind, too, that "semi-matt" or "semi-gloss" will also tend to

Validating Oven Thermal Profiles

Electronics Forum | Fri Aug 15 10:18:42 EDT 2008 | jdumont

There was a discussion on this a few weeks back. Basically if you HAVE to do this because you have an older oven that you dont trust or your customers/ISO force you to do it then just do it monthly on the test board only. Doing it on the test board a

Solder Open/Mild Tombstone on 1206 LED

Electronics Forum | Thu Aug 21 14:38:32 EDT 2008 | Paul M.

I have had a similar problem as this. But, not on that particular type of component. Have your machine place the component, take the PCB over to a microscope and look at the part how it sit's on and in the paste on the pads. You might see that one

Programming the Camalot

Electronics Forum | Wed Aug 27 13:03:10 EDT 2008 | adamcrum

My company recieved an old Camalot dispensing system from a company that we are now building boards for. It is OLD and runs a DOS. I have managed to set up the machine without directions, and have even built a program for it, but I can't get it to ru

no clean flux + wave soldering issue

Electronics Forum | Thu Aug 28 11:31:17 EDT 2008 | patrickbruneel

Matt solder mask finishes gives the widest process window in view of potential amount of residues when using No-Clean. Shiny (glass like) finishes are more sensitive to residues due to lower surface area compared to matt finish. If the shiny finish i

AOI Tabletop Suggestions

Electronics Forum | Tue Sep 16 19:13:28 EDT 2008 | hegemon

Our Mirtec MV3 Benchtop machine came with its own table. Others may or may not. During our evaluation of AOI machines we had 2 other units set up on standard workbenches at times. A solid, shake free table is a MUST, the heavier the better. There i

DEK265GSX >>>motor commumincation error

Electronics Forum | Fri Sep 26 12:16:52 EDT 2008 | bickt

you cannot swap 0-3 only 0-1 or 2-3 they are not the same euro cards. they function very diffrently. if you look you will see there are more chips and circuitry on one set. there are 2 w/red leds and 2 with green leds. at least thats how they soo

New Printer :- Dek Horizon 03i or MPM 125 ??

Electronics Forum | Thu Oct 02 08:09:04 EDT 2008 | pwilson1

Hi All, I am currently in the process of selecting a new stencil printer and have narrowed it down to the MPM125 or DEK Horizon 03i.. We re a UK medium volume production facility running quite a high mix of double sided PCB`s. W

IP3 head 1 not placing parts

Electronics Forum | Tue Oct 21 04:45:13 EDT 2008 | stanyserrao

Head 1 is not placing the parts in production. Same component is placed by head 2. Head 1 camera is camera 12 type and head 2 camera is type 8. Machine re-set done resent proper data and interchanged cameara still same problem was foundd in head 1.

Quad Autoprogram Help Needed

Electronics Forum | Fri Oct 24 07:44:05 EDT 2008 | leemeyer

Yep there are nozzles on both machines. This is a very quirky program. I remember when I first loaded it I couldn't get it to run. I reloaded several times, double checked all of the settings in the autoexec and config.sys files but couldn't get it


sets searches for Companies, Equipment, Machines, Suppliers & Information

convection smt reflow ovens

High Throughput Reflow Oven
See Your 2024 IPC Certification Training Schedule for Eptac

World's Best Reflow Oven Customizable for Unique Applications
2024 Eptac IPC Certification Training Schedule

High Resolution Fast Speed Industrial Cameras.


"Find out how you can receive priority in SMTnet Search with out Sponsor membership."