Electronics Forum | Sun Jan 16 05:22:36 EST 2005 | dorklover664
I�ve worked as an SMT operator for 3 different companies. And have worked with six different types of pick and place machines. I can tell you what I know. The first place I worked at was high volume low mix and we ran Fuji�s. They are by far the best
Electronics Forum | Tue Feb 01 12:43:39 EST 2005 | jbrower
Hi Scott, My Heller is a bog standard Heller 1500 with an edge guide. There is nothing special about it. I would of course love to have a 7 zone oven, but...I have to use what is here at this time. My only concern with a 5 zone oven is the change i
Electronics Forum | Fri Apr 08 16:26:36 EDT 2005 | Grant
Hi, It seems weird that an automated pick and place machine at a board shop would not be up to NASA standards, but placing the components by hand would be. However most SMT will self center a bit, so if your close enough, you should be ok. You rea
Electronics Forum | Fri Apr 22 16:57:10 EDT 2005 | davef
Suppliers are: * Contax Ltd Little Park Farm Road Segensworth West Fareham, Hants, PO15 5SJ UK +44 1489 885808 Fax: +44 1489 885553 * Leister Process Technologies Riedstrasse Sarnen LCRN, 6060 Switzerland 011-41-416627467 Fax: 011-41-416627480 * mt
Electronics Forum | Wed May 04 03:12:02 EDT 2005 | Dr . Klein
Hello all. I need some advice for first article inspection process. I will explain my problem with this process: In our site we are doing a manually FAI before reflow for every assembly. One of the steps is to check the writing on each QFP or BGA (e
Electronics Forum | Thu May 05 09:46:04 EDT 2005 | davef
Board fab, Defects, Pad coatings, Gold black plague articles 1 Nick Biunno's article: http://www.nukcg.org/downloadfiles/Hadco%20on%20Immersion%20Gold%20failures.pdf 2 George Milad's article: http://www.circuitree.com/ct/cda/articleinformation/featu
Electronics Forum | Mon May 16 18:03:30 EDT 2005 | davef
Key Issue: Will this machine solder your boards? You never know until you solder one. Any other avenues of analysis involve substantial risk. Flux Selection * High or low solids * VOC or VOC-free Solder Alloy * If using lead-free, avoid stainles
Electronics Forum | Wed Jun 22 06:18:07 EDT 2005 | dougs
We started looking at tabletop AOI systems last year, one of the main criteria, as we are a SC was that the sales engineer programmed one of our boards in front of us so we could see just how easy to program it was, also high on the list was performa
Electronics Forum | Sat May 21 08:22:42 EDT 2005 | davef
We agree with the previous poster. 50 pounds sounds like a lot. We don't know: * How often you dedross? * What method you use for dedrossing? * What portion of your dross that is dross versus solder? * How many boards do you run between drossings?
Electronics Forum | Thu Jun 02 03:31:29 EDT 2005 | Rob
The Fuji flexible model is the XP, (Stay away from the QP!) but (as a previous poster mentioned) I'm used to the Bomb proof Chipshooters. They still make these and from memory I think they are around $350,000 each. They will place BGA's and reasona
Main Products: 1. Original new and Original Used SMT/AI Spare Parts. 2. SMT Equipments And Related Machine( SMT Calibration, SMT Feeder Carts,Conveyer etc.) 3. Maintenace and Repair Service Pre-Sales Service Provide details ab
Manufacturer's Representative / Manufacturer / Equipment Dealer / Broker / Auctions / Consultant / Service Provider
Building A, Jiepeng Square, Fuyong
Shenzhen, 30 China
Phone: 0755-33578694