Electronics Forum: used machine (Page 536 of 656)

Re: First Article

Electronics Forum | Thu Oct 07 04:46:03 EDT 1999 | Wolfgang Busko

| Our first article inspection after machine placement can take several hours depending on the complexity of the board. The operator visually checks the board against the drawing and bill of material. I'd be interested to hear if there are any other

Re: MicroBGA printing problem

Electronics Forum | Mon Sep 20 17:26:22 EDT 1999 | Earl Moon

| I've had some trouble pasting a test board for a MicroBGA trial. Most of the paste remains in the stencil apertures. | The stencil is 6 mil thick, laser cut and electo-polished. | The apertures are 12 mil in diameter with 20 mil pitch. | We are usi

Re: Preventive Maintenance Software

Electronics Forum | Tue Sep 07 12:05:39 EDT 1999 | Brad Kendall

| I am looking for some PM software to use throughout my Electronics factory. Currently, we have a manual system consisting of check-off sheets, log-books, etc. Ideally I would like a system that would throw-up a flag (perhaps by e-mail) when PM is

Re: Where can I get delmat material

Electronics Forum | Wed Aug 25 10:51:55 EDT 1999 | Peter Barton

| Can anyone tell me where I can get a good lightweight material to use for a soldering fixture? I need to make various fixtures to hold LED's vertical during the soldering process, and keep them from floating up off the board surface. | | At a dif

Re: Wave solder edge covers

Electronics Forum | Wed Jun 30 17:58:01 EDT 1999 | Boca

| My guess would be trapped flux continuing to be active after soldering. Is the tarnish there immediately after exiting the machine? Do you remove the mask and wash right away? If the solder is reflowing under the mask on the component side it wo

Closer lead more soldering bridge by using spray flux

Electronics Forum | Tue Jun 08 08:40:37 EDT 1999 | Wister

Hi,my master How to iron out such soldering bridge with below conditions: 1.The component(Harness)lead pitch is 2.0mm,the lead length is 3.2mm. 2.PCB width is 1.6mm.Pad size is 1.65mm.Its a single copper PCB 3.using spraying fluxer and no-clean fl

Closer lead more soldering bridge by using spray flux

Electronics Forum | Tue Jun 08 08:38:15 EDT 1999 | Wister

Hi,my master How to iron out such soldering bridge with below conditions: 1.The component(Harness)lead pitch is 2.0mm,the lead length is 3.2mm. 2.PCB width is 1.6mm.Pad size is 1.65mm.Its a single copper PCB 3.using spraying fluxer and no-clean fl

Wrote some software at home ................... (plug)

Electronics Forum | Wed May 12 23:33:04 EDT 1999 | Matt

WARNING: This is a plug. I have read post on this site where the question is raised: "My machine can do 80 units per hour, but I am only getting 35 - WHY?" Well I have written w95/database code that reads FUJI output files (CPII,CPII,IP2 etc) and d

Re: electronics assembly clip art

Electronics Forum | Tue Mar 23 12:55:47 EST 1999 | Dave F

| I am looking for clip art images of electronics assembly. Images like wave soldering, surface mount components, soldering irons... just general assembly graphics. Many sites have different individual images that they use I was just wondering if a

Re: FUJI CP Placements

Electronics Forum | Thu Jun 03 01:33:40 EDT 1999 | Bubba

| Here is my question. We have several fuji CP's in our shop, every once in a while the first couple of parts placed are off the pads. When we move the parts further down in the sequence they are fine. What is going on? Has anyone had this problem an


used machine searches for Companies, Equipment, Machines, Suppliers & Information