Electronics Forum: wave soldering defect (Page 1 of 578)

Blowholes during wave soldering

Electronics Forum | Tue Sep 11 19:04:28 EDT 2007 | hakerem

Hi Shrek - Not sure why you think adjusting dwell time and preheats is a sales pitch, but I do appreciate your candor. These are proven, widely used techniques for attacking, eliminating and preventing the recurrence of blowholes. Since it is so ea

wave soldering two times

Electronics Forum | Sat Aug 04 03:39:39 EDT 2007 | ahdo

Good day, can i seek an advice regarding wave soldering. Will it be advisable to reload the board two times to improve its barrel fill volume? If yes, what is the maximum number of times we can repeat wave soldering on the same board. If no, what

wave soldering conveyor angle

Electronics Forum | Wed May 12 07:34:42 EDT 2004 | RLeonard

The standard machine is set from the factory at 7-9 degrees, 7 is the most standard, why are you considering the change? before doing any thing to the machine, first identify why? what type of defects are you seeing? I have found, depending on the t

Fine pitch wave soldering

Electronics Forum | Thu Sep 14 11:56:47 EDT 2006 | russ

I think you have your pitch wrong but anyway, I have never had success with wave soldering anything less than 50 mil pitch. On a QFP I have had good luck on three sides of 25 mil but never all four sides and without defects. Mask 'em off and hand s

Board wave soldering

Electronics Forum | Mon May 19 10:35:58 EDT 2008 | samir

I agree with RealChunks. The application of any of these "wave solder process control tools" is dependant on how the shop is run. At some shops, PM is inconsistent and slacked off on. At other shops, there is no technical expertise at the operator

AOI for defect detection at soldering process

Electronics Forum | Wed Apr 19 04:38:49 EDT 2006 | ge_lim

Hi Refering to the Apr edition of SMT , page 24 to 29, anyone got experience on implementing the AOI or 3D x ray : a) What is the pros and cons? b) What is the trend in the PCBA industry for wave soldering inspection? c) Will this implementation co

wave soldering and solder bridge

Electronics Forum | Mon Dec 17 11:55:08 EST 2007 | chef

I recently had the same problems, solder bridges on every thing I made, different customers boards, etc. I wave with no-clean flux. As I sorted out problems (pin holes, blow holes, splatter, etc.) I found a lot of variable factors. I changed flux,

JT Universal wave soldering machine

Electronics Forum | Sun Oct 08 23:37:37 EDT 2006 | zoltans

Hi, Has anyone got first hand experience with the JT wave soldering machines, WS series? I use a low solid VOC free flux and it seems I have problems atomizing the flux properly and this generates soldering defects, leaving lumps and big solder bal

JT Universal wave soldering machine

Electronics Forum | Thu Oct 05 23:44:55 EDT 2006 | zoltans

Hi, Has anyone got first hand experience with the JT wave soldering machines, WS series? I use a low solid VOC free flux and it seems I have problems atomizing the flux properly and this generates soldering defects, leaving lumps and big solder bal

PCB bows after wave soldering

Electronics Forum | Fri Jun 18 17:36:10 EDT 2010 | sid

Good afternoon all, I have been trying to find a solution to a defect I just noticed. After stencil printing and smt part placement on the secondary side of my boards, I run them through a wave soldering system. All my components got soldered perfe

  1 2 3 4 5 6 7 8 9 10 Next

wave soldering defect searches for Companies, Equipment, Machines, Suppliers & Information

High Throughput Reflow Oven

Nozzles, Feeders, Spare Parts - Siemens, Fuji, Juki, Yamaha, etc...
Selective soldering solutions with Jade soldering machine

Reflow Soldering 101 Training Course


"Heller Korea"