SMT, PCB Electronics Industry News

Calibration of Rosemount Transmitter

Dec 02, 2021

1. Zero Calibration

When adjusting the transmitter, please turn off the protection setting, which is usually the red switch in front of the meter and its status may be ON or OFF.

If it is ON, you will not be able to make the calibration adjustment.



Rosemount Differential Pressure Transmitter 1151DP, Type Supply:45 VDC MAX Output:4-20mA

Figure 1: Rosemount Transmitter 1151DP5E22M6Y1

Calibration Steps

First, ventilate the transmitter, and connect measuring circuit with the manual operator.

Then, operate on the manual operator as follows.
Calibration Steps
Finally, calibrate the transmitter through zero calibration according to the manual operator.


It is important that the zero calibration must be for the transmitter whose output is within 3% around zero.

2. DAC Calibration (Output Calibration)

The output calibration means to calibrate the signal output conversion from digital-to-analog (DAC).
Operate on the manual operator as follows.



DAC Calibration

And set the control loop as manual mode.

Before confirming, notice that if the positive and negative wiring is correct.
Finally, the output of the field device is set to 4mA, and the output of the transmitter is 4mA. Then record the actual value of the reference table, and input the value on the transmitter.

Check whether the output of the manual operator is consistent with the value of the reference table. If it is consistent, change the output to 20mA, and then repeat the operation until it's accurate. If not, you should continue to input the reference value and inspect whether it is consistent with the manual operator output.
Finally, set the control loop as automatic control.



Rosemount High Static Pressure Transmitter 1151HP Type Supply:45 VDC MAX Output:4-20mA

Figure 2: Rosemount Transmitter 1151HP7S22M4B1

3. ADC Calibration (Sensor Calibration)

The sensor calibration is to calibrate the analog-to-digital converter (ADC). The main work to be done is zero calibration and full calibration. Full calibration requires three times the accuracy of the transmitter. Operate on the manual operator as follows.
ADC Calibration
If the accuracy value of transmitter is 0.25mA, the lower limit output will be 0.06mA.

Related Info

Benefits of Rosemount Fieldbus Transmitter
Rosemount Transmitter Series 1151, 2088, 2051, 3051CA, 3051S

Thank you for you reading and more information please visit https://okmarts.com/news/transmitter.html

Dec 30, 2021 -

What does the Tire Pressure Sensor Fault Mean?

Dec 30, 2021 -

Car AC Compressor Troubleshooting-- Best Suggestions

Dec 29, 2021 -

Where is Servo Motor and Servo Drive Used?

Dec 29, 2021 -

Basics of Servo Motor You Should Know

Dec 28, 2021 -

How to Replace Refrigerator Compressor

Dec 28, 2021 -

When You Should Use an Absolute Encoder - Pros and Cons of Different Absolute Encoders

Dec 27, 2021 -

6 Reasons for Refrigeration Compressor Not to Start

Dec 27, 2021 -

Why Refrigeration Compressor Oil Deteriorates & How to Add Oil

Dec 26, 2021 -

Japanese Giant Mitsubishi Heavy Industries Goes Into Central Air Conditioners for Home Use

Dec 26, 2021 -

High Temperature Mulfunction of Screw Compressor and Solutions

92 more news from OKmarts Industrial Parts Mall »

Sep 12, 2024 -

BENTLY NEVADA 330103-00-14-10-01-00

Sep 12, 2024 -

BENTLY NEVADA 330703-000-100-10-02-00 Sensor

Sep 12, 2024 -

BENTLY NEVADA 88984-02 3300XL8MM

Sep 12, 2024 -

SIEMENS 6EW1810-3AA

Sep 12, 2024 -

5370-CVIM Vision Processor Module

Sep 12, 2024 -

ABB DAI04 1 year warranty

Sep 12, 2024 -

LP HCW222A PLC MODULE

Sep 12, 2024 -

ABB DSRF182 57310255-AL

Sep 12, 2024 -

CTI 2501 901C-2501 Output Module

Sep 12, 2024 -

WOODWARD 8237-1481 Rev B Digital Controller

See electronics manufacturing industry news »

Calibration of Rosemount Transmitter news release has been viewed 493 times

High Precision Fluid Dispensers
High Throughput Reflow Oven
Reflow Oven

Win Source Online Electronic parts