ETA Pyxis Series CBS Reflow Oven If you could not find any similar items you want, you may send some photos to us. because our catalog and website haven't included all of our products. Reflow Oven, Reflow Soldering, Reflow Soldering Oven,
Parts & Supplies | Circuit Board Assembly Products
1) 190*130mm/10up, FR-4, Tg 135, CTI 175-225V 2) Dielectric constant(Er): 4.4-5.2 3) 2 layers, 1.6mm thick, 1 oz 4) Min. hole size: 0.3mm 5) Min. track/space: 4/4 mils 6) LPI Solder mask/White legend 7) Fiducial mark, tooling strips, mounting holes
Used SMT Equipment | General Purpose Test & Measurement
ESPEC EWPT286-CCA Walk-in Environmental Test Chamber (2000) Brand: ESPECModel: EWPT286-CCASerial Number: 304468Mfg year: December 2000Hours: 14686 HursTemperature range:-10 up to 85 CelsiusRefrigerant Type:404A (16 lbs)Power: 208 VAC, 3 Ph, 60 Hz.Wei
Parts & Supplies | Air / Vaccuum
FUJI H4264A BEARING 7205TIDBT/GMP-5 FUJI H4265D Bearing WA673ZZA FUJI H4265T Bearing AC6-16P5 QP341/Head (Set=2 pcs) FUJI H4267A BEARING ST-8B FUJI H4269A BEARING ST35UUB FUJI H42726 BEARING NB-5 CP-6/ST3,10,12,13 FUJI H4274A BEARING SLIDE LM8U
Electronics Forum | Tue Nov 17 20:46:13 EST 2020 | williamaxler
Trying to get a CS400D working. We are programming a 10up board and are trying to set permanent offsets in the program and we cannot get them to read in. Any help?
Electronics Forum | Tue Jul 27 11:34:05 EDT 2004 | C Lampron
Nippy, This is exactly what we are seeing. The exessive pads are all on one side of the board. This is a 10 up panel 5x2. All of the QFP's on one side on the panel are not releasing or are not gasketing and causing bridging. So the defects are rangi
Electronics Forum | Tue Feb 02 17:10:03 EST 2010 | flipit
Remember this is a 30 layer PCB. If it is built in a multi up panel, there is lots of room for error. Lets say there are 10 circuits per panel. Say you have a 10% scrap rate that happens randomly within the 10 up panel of circuits. Apply this 10%
Electronics Forum | Fri Dec 07 09:43:04 EST 2001 | Russ Steiner
I have a mixed technology PCB that has SMT all on bottom, TH parts on both sides (Yes, I realize that's bad. Can't be avoided.) We have designed a 10-up panel, 2 x 5 array. There are 50 leads per bd, 500 per panel. How much time is reasonable to a
Electronics Forum | Mon Jul 17 16:38:41 EDT 2006 | dave
Guys, My problem is that I have a 10 up panel and I have to use a selective pallet to run it thru the wave process due to SMT on bottomside. However the yields are very poor. We have done everything to improve them with some good improvements along
Electronics Forum | Thu Aug 09 14:00:51 EDT 2018 | tey422
To me the most challenge would be the printing step. If you can print it, you should able to run it with SMT. We ran similar thickness flex boards before. But it's long flex with small stiffener at both ends, and it was 10up array. You need fixture
