Electronics Forum | Tue Jun 26 19:48:29 EDT 2001 | davef
Information a SIR test vehicle can be found in IPC-9201, SIR Handbook [http://www.ipc.org]. Common test boards are: * IPC-B-24 (copper and HASL, FR-4 and polyimide) * IPC-B-36 (bare copper and HASL, FR-4 and polyimide) * IPC Phoenix board (bare copp
Electronics Forum | Mon May 15 12:36:12 EDT 2017 | edhare
I don't believe there should be any issues with > the HASL finish. The issue is how long on the > shelf and is a bake out required to remove > moisture from PCB, as in any FR4 PCB's that may > have had time to absorb moisture. > I don't believe
Electronics Forum | Mon Jun 14 14:39:12 EDT 2004 | davef
HASL Thickness: * HADCO DFM manual specifies a nominal thickness of 50-1500uin with an option for 100-1000uin * Merix DFM manual specifies 30-200uin IPC-6012, Class 1, 2, 3 do not spec a HASL thickness at all but only require that full coverage is m
Electronics Forum | Wed Oct 03 09:56:51 EDT 2001 | Claude Tremblay
Hello everyone We have a QFP-308 (0.20" pitch)on a board and we have a lot of opens after reflow. We checked our profil by installing thermocouples on the pads of the component and everythings seems OK. We checked the coplanarity of the leads and it
Electronics Forum | Wed Sep 21 16:25:43 EDT 2005 | GS
IPC-7525 tells you how to make stencil apertures for BGA IPC-7095 tells you how much should be the paste volume in order to get a reliable BGA solder joint. How are your PCB finisced? (HASL, ENIG, OSP, etc?) In case of not HASL, it could be necessa
Electronics Forum | Wed Nov 28 22:33:24 EST 2007 | davef
There is no specification for lead-free HASL. You can use any lead-free solderability protection that meets your customer requirements. Use IPC-9701 �Performance Test Methods and Qualification Requirements for Surface Mount Solder Attachments� to ass
Electronics Forum | Mon Jun 14 16:49:08 EDT 2004 | Dreamsniper
Can I manually tin them with solder specially the BGA's. Will that improve the solderability? What about corrosion of the copper? will it be prevented with the above process considering that after tinning of solder the solderability became acceptable
Electronics Forum | Tue Sep 02 22:21:26 EDT 2008 | davef
IPC-6012 Table 3-2. States "Fused tin-lead or solder coat - Coverage and Solderable". The lack of any specific dimension criteria doesn't make this any less a requirement. There must be complete coverage of solder on the land, and it must be wettable
Electronics Forum | Fri Aug 13 17:45:43 EDT 2010 | bradlanger
Boards with the LF hasl finish applied too thin will genrally pass the IPC test. That is some pretty agressive flux they call out. The boards usually wave solder just fine as well. Reflow is where the you see the problem.
Electronics Forum | Wed Apr 16 19:23:52 EDT 2008 | molos21
I think you are close to the problem when you expect the pcb having a problem. When I look at your different pics I saw that your via holes looks like this pcb has a hasl finish... and when i look at Q 14 this picture tells me that the pcb is not an
IPC is the trade association for the printed wiring board and electronics assembly industries.
Training Provider / Events Organizer / Association / Non-Profit
3000 Lakeside Drive, 309 S
Bannockburn, IL USA
Phone: 847-615-7100
