Electronics Forum: selective soldering no barrel fill (28)

THM Solder barrel fill issues on 93 mils board

Electronics Forum | Wed Aug 21 17:03:13 EDT 2013 | hegemon

I think your pre-heat temp is a little low for SAC 305 Soldering. Especially with a Pallet. You might want to try to add some time and temp to get the PWB itself preheated up to 150-160C. That should help with the barrel fill. Make sure your board

THM Solder barrel fill issues on 93 mils board

Electronics Forum | Wed Aug 21 09:09:50 EDT 2013 | wcheew

I am having solder barrel fill issues on THM component, we follow, we follow IPC 610 E requirement. The barrel fill issues happen on signal & ground pin at connector & E-cap. I found out that most of the insufficient solder happen on the connector ag

Industry News: selective soldering no barrel fill (5)

Kester Launches SELECT-10™ Selective Solder Flux

Industry News | 2016-04-22 10:20:35.0

Kester is proud to announce the launch of SELECT-10™Selective Solder Flux, a zero-halogen no-clean liquid flux designed specifically for the needs of the selective soldering process. As part of Kester’s portfolio of high reliability products, SELECT-10™ has passed IPC SIR testing as a raw and partially activated flux. Sustained activity within the flux allows for good barrel fill in challenging and high temperature applications. Specific to selective soldering, SELECT-10™ does not spread beyond the spray pattern and will not clog nozzles. SELECT-10™ is classified as ROL0 flux under IPC J-STD-004B.

Kester

Cobar Expert Gerjan Diepstraten to Discuss Reflow Soldering during IPC Midwest 2012 Conference

Industry News | 2012-07-25 15:16:14.0

The Balver Zinn Group announces that Cobar BV’s Gerjan Diepstraten will present a paper titled “Reflow Soldering Equals Wave Soldering Plus One” at the upcoming IPC Midwest Exhibition & Conference

Balver Zinn

Technical Library: selective soldering no barrel fill (1)

Position Accuracy Machines for Selective Soldering Fine Pitch Components

Technical Library | 2015-02-27 17:06:01.0

The drive towards fine pitch technology also affects the soldering processes. Selective soldering is a reliable soldering process for THT (through hole) connectors and offers a wide process window for designers. THT connectors can be soldered on the top and bottom side of boards, board in board, PCBs to metal shields or housing out of plastic or aluminum are today's state of the art. The materials that are used to make the solder connections require higher temperatures. Due to the introduction of lead-free alloys, the boards need more heat to get the barrels filled with solder. This not only affects the properties of the flux and components, but the operation temperatures of solder machines become higher (...)First the impact of temperature will be discussed for the separate process steps and for machine tooling. In the experimental part measurements are done to verify the accuracy that can be achieved using today's selective soldering machines. Dedicated tooling is designed to achieve special requirements with respect to component position accuracy.

Vitronics Soltec

Express Newsletter: selective soldering no barrel fill (1011)

SMTnet Express - December 23, 2015

SMTnet Express, December 23, 2015, Subscribers: 23,927, Members: Companies: 14,845, Users: 39,621 PCB Fabrication Processes and Their Effects on Fine Copper Barrel Cracks Edward Arthur, Charles Busa, Melissa Durfee, Chad Gibson, Wade Goldman P

SMTnet Express - February 27, 2015

SMTnet Express, February 27, 2015, Subscribers: 22,336, Members: Companies: 14,215, Users: 37,692 Position Accuracy Machines for Selective Soldering Fine Pitch Components Gerjan Diepstraten; Vitronics Soltec B.V. The drive towards fine pitch

Partner Websites: selective soldering no barrel fill (42)

Nordson ACE KISS 103 ILDP Selective Solder 2015 - Lewis and Clark

Lewis & Clark | https://www.lewis-clark.com/product/nordson-ace-kiss-103-ildp-selective-solder/

Nordson ACE KISS 103 ILDP Selective Solder 2015 - Lewis and Clark Skip to content My Cart:  0 View Cart Checkout No products in the cart. Subtotal

Lewis & Clark

Soldering Thick PCB's With 3 oz Copper - EPTAC - Train. Work Smarter. Succeed

| https://www.eptac.com/faqs/ask-helena-leo/ask/soldering-thick-pcbs-with-3-oz-copper

: How do I get a flow through on a 120 thick pcb with 3 oz copper layers. I saw your soldering tip #37. We have tried multiple applications but with no consistent success


selective soldering no barrel fill searches for Companies, Equipment, Machines, Suppliers & Information

Sm t t t t t t t t t t net
  1 2 3 4 5 6 7 8 9 10 Next