Electronics Forum: mydata machine not placing (Page 1 of 38)

MyData DPak not placing

Electronics Forum | Mon Jul 29 09:43:31 EDT 2013 | cyber_wolf

First figure out which centering phase it is using when the part gets rejected. Then run the machine in step mode and watch whats going on.

MyData DPak not placing

Electronics Forum | Mon Jul 29 13:34:28 EDT 2013 | dontfeedphils

Usually the reason it will fail a part like that when you are using mechanical centering is because the part is usually picked so off center because of the body shape. So when the centering jaws close to push the part to center they give up and fail

MyData DPak not placing

Electronics Forum | Fri Jul 26 11:20:33 EDT 2013 | gnus

Hi all, I'm having issues placing 7 pin DPak packages. I'm using mechanical centering with four centering phases (one for each orientation). Tool used is A24S. Machine picks up the part but will reject it when centering the part. I have measured all

MyData DPak not placing

Electronics Forum | Mon Jul 29 13:48:20 EDT 2013 | cyber_wolf

We have placed millions of DPAKS on our Mydatas without issues. Usually the crosshairs need to be just slightly to the right of the dimple when trimming. We do not use high centering force. Please tell us exactly what the error message is.

MyData DPak not placing

Electronics Forum | Mon Jul 29 11:17:45 EDT 2013 | kjs123p

Is it failing the optical measurement or a vac measurement? I know that sometimes there is a dimple on the face which can cause rejects due to low vac. I am not sure about the MyData though.

MyData DPak not placing

Electronics Forum | Fri Jul 26 12:41:43 EDT 2013 | dontfeedphils

Check the centering force, and change it to High, if it isn't already.

MyData DPak not placing

Electronics Forum | Tue Jul 30 11:58:50 EDT 2013 | gnus

Seems to pick up and place fine now. No idea why, didn't change a thing. Thanks for the advice everyone!

Quad 4c not placing components

Electronics Forum | Wed Sep 04 13:40:46 EDT 2019 | smrsteve

Hello DWL, Thanks for the response. I've measured the components with a micrometer and set the sizes. Maximum tolerance on my machine is 20%, and that's what I'm using. If I do a manual scan, the measurements are exactly right (and what I've set up

Quad 4c not placing components

Electronics Forum | Wed Sep 04 09:47:41 EDT 2019 | smrsteve

Hello All, I've just bought a Quad 4c pick & place machine. It's so close to actually building boards, but just doesn't quite get there. I was wondering if there's somebody out there with experience of these machines that might be able to help...?

Quad 4c not placing components

Electronics Forum | Wed Sep 04 13:58:36 EDT 2019 | smrsteve

Hello Bobpan, Thanks for the response. 1. Function 30 gives me a consistent 182-185, even after nozzle changes. I can vary this by changing mod code 15 and I have been advised to aim for 90-110, but it doesn't seem to make any difference so I've go

  1 2 3 4 5 6 7 8 9 10 Next

mydata machine not placing searches for Companies, Equipment, Machines, Suppliers & Information

Selective soldering solutions with Jade soldering machine

High Throughput Reflow Oven
See Your 2024 IPC Certification Training Schedule for Eptac

World's Best Reflow Oven Customizable for Unique Applications
SMT feeders

Wave Soldering 101 Training Course
Equipment Auction Automotive Electronics Supplier - Closure of Tier-One SMT Dvision: (10) ASM & Universal SMT Lines & Feeders Equipment as-new-as 2019! Dek | Koh Young | Speedline | Vitronics | Viscom

Software programs for SMT placement and AOI Inspection machines from CAD or Gerber.