| https://www.eptac.com/blog/40-years-of-industry-insights
. I sought guidance from Brenda Clunie, who helped me understand the operational aspects and the procedures for establishing training partnerships that allow EPTAC to conduct its classes
GPD Global | https://www.gpd-global.com/pdf/doc/Dispense-System-User-Guide-22100079K.pdf
depending on the materials dispensed. Remove all contaminated parts and dispose of per MSDS / SDS instructions and local laws. • Chemical Safety: Changes to the typical process chemistry or to the equipment could alter the anticipated environmental impact
| https://www.eptac.com/category/upcoming-webinars/shown.bs.collapse/page/8/
purpose states: “…describes materials, methods, and acceptance criteria for producing soldered electrical and electronic assemblies”. J-STD-001 also states: “… the intent of this document is to rely on process control methodology to ensure consistent
GPD Global | https://www.gpd-global.com/co_website/pdf/doc/Advanced-FPC-Real-Time-Controller-User-Guide-22940009.pdf
The Online/Offline button on the front of the controller toggles the controller between online and offline states. Numerous process settings can be edited regardless of Online/Offline status. Offline Offline status is the non-operational/power up
GPD Global | https://www.gpd-global.com/pdf/doc/Advanced-FPC-Real-Time-Controller-User-Guide-22940009.pdf
The Online/Offline button on the front of the controller toggles the controller between online and offline states. Numerous process settings can be edited regardless of Online/Offline status. Offline Offline status is the non-operational/power up
| https://www.eptac.com/category/upcoming-webinars/shown.bs.collapse/page/9/__/ais-highlight__/__/ais-highlight__/-36.868%25/134.936%25/129.432%25/-36.868%25/__/ais-highlight__/-27.7%25/%3C/em%3E/134.936%25/%3C/em%3E/-27.7%25/gtm.start/gtm.start/129.432%25/gtm.start/gtm.start/-36.868%25/page/2/134.936%25/page/8/
conditions are required: Target – 2x Db’s Acceptable – 1, 2 or 3x Db’s Defect – < 1x Db Process Indicator > 3x Db’s When inspecting a cable splice, another cable of the same gauge (or specialized tooling) may be used by intersecting (off 90 degrees) at one end
GPD Global | https://www.gpd-global.com/co_website/pdf/doc/Packing-Instructions-MAX-Series-Dispenser-22290016.pdf
& Packing Instructions Preparation Instructions 5. Stabilize Gantry Use one of the following methods to secure the gantry: Stacked Foam Method If conveyor rails are present, a gap of approximately 6
GPD Global | https://www.gpd-global.com/pdf/doc/Packing-Instructions-MAX-Series-Dispenser-22290016.pdf
& Packing Instructions Preparation Instructions 5. Stabilize Gantry Use one of the following methods to secure the gantry: Stacked Foam Method If conveyor rails are present, a gap of approximately 6
GPD Global | https://www.gpd-global.com/co_website/pdf/coating/SimpleCoat-Operation-Guide-23100600.pdf
hazardous materials or chemicals used in the system except for the conformal coating application/process. Location The System must be placed in an area that is level, and away from standing water, overhead leaks or spray areas. Operating Environment
GPD Global | https://www.gpd-global.com/pdf/doc/Dispense-System-Service-Guide-22290008G.pdf
. 11/11/2014 2.7 New • User Controls Access added. • MAX II footprint dimensions updated. Improvements • MAX Series dimensional illustrations updated with optional process view arm and monitor. etc., etc