Technical Library | 2020-02-14 14:43:21.0
To meet the steady increase in technical requirements for electronic components, potting media properties must be extremely precise. Rheology, viscosity, filler content and curing behavior are only a few of the factors that play a role in their practical use. However, the growing complexity of materials often negatively impacts the ability to process or dispense them. In this case, material preparation and feeding systems specially designed for this purpose are required. These systems optimally prepare the material for the actual application and ensure homogeneous feeding to the dispensing system.
Technical Library | 2020-02-13 08:41:18.0
Efficient bonding, sealing and potting has a major influence on the sustainable function and safety of electronic components. The key to success here lies in the comprehensive view and control of process engineering. Here it pays to seek collaboration with the systems and the material manufacturer during the very early stages of the project. This is because dispensing systems must be selected for compatibility with the workpiece and the adhesive, sealant or potting compound used. And there are also other factors that play an important role in designing the optimum dispensing system:
Technical Library | 2018-08-23 07:47:57.0
Simply put, the proper system design and use of vacuum in the potting process can make the difference between a mediocre part and a perfect part. Air entrapment is inevitable whether you utilize syringes, cartridges, pails, or drums of material in the process.
Technical Library | 2015-08-18 18:39:13.0
Jetting Valve Technology Superior to Needle Dispensing Compared to traditional needle dispensing technology, jetting valve technology is the most effective method for quick and accurate fluid dispensing. Injection technology has many advantages, it provides a combination of high-speed, high quality and low cost production for fluid dispensing processes. Instead of putting focus on getting the application done, jet dispense technology focuses on performance, providing applications like underfill, potting and encapsulation with more precision than ever before. Improved Fluid Dispensing Speed and Accuracy Non-contact jetting valves offer a significant advantage over traditional needle dispense valves. Jetting Valve Dispenser precision reaches to 200µm with dot diameter or line width as small as 250µm and volumetric dispensing down to .0036µl. Minimum space between lines is 180µm and maximum fluid dispense speed is 200 dots/second. The following video illustrates quick, accurate fluid dispensing for an LED packaging application.
Technical Library | 2021-07-28 18:35:13.0
The performance of electronic components is compromised by factors such as bubbles in the potting medium. Increasing numbers of applications – particularly in the automotive and electronics industries – therefore require completely bubble-free dispensing methods. This is where potting in a vacuum comes into focus. The widespread school of thought about this technology is that it is too complicated, too expensive and too slow. But a closer look shows that this view is incorrect. This is a mastered technology. As for costs, the calculation basis is key, since usually the potting and vacuum method is only considered after the required potting quality cannot be achieved reliably any other way. Under total cost of ownership assessments, higher system costs no longer play a key role, since component failure would result in much higher subsequent costs. And now there are proven solutions for high production volumes and/or shorter cycle times. This whitepaper explains when potting in a vacuum is ideal for your projects and what to be aware of.
Technical Library | 2018-06-18 13:43:56.0
Thermal influences can significantly compromise the service life, capacity and especially the operational safety of HV batteries. In order to prevent damage due to excessive temperatures, large quantities of heat-conducting potting media are used here. Scheugenpflug has developed a new system solution for fast and reliable application of these materials.
Technical Library | 2023-07-27 18:41:40.0
Diabetes affects many millions of people worldwide. New technology for real-time glucose measurement replaces the usual unpleasant pricking of a finger: a sensor located in the subcutaneous tissue of the diabetes patient measures the glucose values and transmits them to a receiver. Production of such medical wearables calls for high-precision dispensing systems for applying very small amounts of UV adhesives to medical PCBs and for integrated system concepts to achieve this. A perfect task for Scheugenpflug.
Technical Library | 2019-05-01 15:19:19.0
"Sealing" in dispensing and potting technology describes a process in which sensitive electronics surfaces are coated with a very thin layer of casting resin or protective varnish. It serves to protect against environmental influences and corrosion, resulting in a longer service life and operational reliability of the components. To ensure that the material is distributed homogeneously across the surface, this well-known "conformal coating" process is employed using low-viscosity casting resins.
| 1 |
