Technical Library | 2023-11-06 17:08:44.0
A new process has been developed for RF shielding on compact electronic communications devices using automated solder paste dispensing. The process is known as Shield Edge Interconnect (SEI). SEI designs enable parts to be processed though underfill before placing of the RF shield and allows more complete use of valuable PCB real estate to achieve reduced form factor requirements and/or for added components on products such as smartphones and tablets. The reduced form factor creates challenges for the assembly of those devices. This process, enabled by Speedline dispensing technology, relies on extremely accurate dispensing of solder paste on copper traces located along the outer edge of the PCB. The result is a robust process solution for SEI in which proprietary closed loop dispenser, pump, vision, and software technologies enable a high volume manufacturing (HVM) process.
Technical Library | 2007-10-25 18:39:07.0
More and more substrate designs require signals paths that can handle multi-gigahertz frequencies [1-3]. The challenges for organic substrates, in meeting these electrical requirements, include using high-speed, low-loss materials, manufacturing precise structures and making a reliable finished product. A new substrate technology is presented that addresses these challenges.
Technical Library | 2021-08-18 01:27:15.0
The growing interest towards thinner and conformable electronic systems has attracted significant attention towards flexible hybrid electronics (FHE). Thin chip-foil packages fabricated by integrating ultra-thin monocrystalline silicon integrated circuits (ICs) on/in flexible foils have the potential to deliver high performance electrical functionalities at very low power requirements while being mechanically flexible.
Fraunhofer EMFT Research Institution for Microsystems and Solid State Technologies
Technical Library | 1999-08-09 11:36:27.0
Shrinking process technologies and increasing design sizes continually challenge design methodologies and EDA tools to develop at an ever-increasing rate. Before the complexities of deep submicron (DSM), gate and transistor delays dominated interconnect delays, and enabled simplified design methodologies that could focus on device analysis. The advent of DSM processes is changing all of this, invalidating assumptions and approximations that existing design methodologies are based upon, and forcing design teams to re-tool. High-capacity parasitic extraction tools are now critical for successful design tape-outs.
Technical Library | 2013-11-27 16:54:01.0
The need in complexity for microwave space products such as active BFNs (Beam Forming Networks) is increasing, with a significantly growing number of amplitude / phase control points (number of beams * numbers of radiating elements). As a consequence, the RF component’s package topology is evolving (larger number of I/Os, interconnections densification ...) which directly affect the routing and architecture of the multilayer boards they are mounted on. It then becomes necessary to improve the density of these boards (...) This paper will present the work performed to achieve LCP-based high density multilayer structures, describing the different electrical and technological breadboards manufactured and tested and presenting the results obtained.
Technical Library | 2014-05-29 13:48:14.0
Electronics packaging based on stress-engineered spring interconnects has the potential to enable integrated IC testing, fine pitch, and compliance not readily available with other technologies. We describe new spring contacts which simultaneously achieve low resistance ( 30 μm) in dense 2-D arrays (180 ~ 180-µm pitch). Mechanical characterization shows that individual springs operate at approximately 150-µN force. Electrical measurements and simulations imply that the interface contact resistance contribution to a single contact resistance is This paper suggests that integrated testing and packaging can be performed with the springs, enabling new capabilities for markets such as multichip modules.
Technical Library | 2014-11-06 16:43:24.0
This paper summarizes the results of recent investigations to examine the effect of electroless nickel process variations with respect to Pb-free (Sn-3.0Ag-0.5Cu) solder connections. These investigations included both ENIG and NiPd as surface finishes intended for second level interconnects in BGA applications. Process variations that are suspected to weaken solder joint reliability, including treatment time and pH, were used to achieve differences in nickel layer composition. Immersion gold deposits were also varied, but were directly dependent upon the plated nickel characteristics. In contrast to gold, different electroless palladium thicknesses were independently achieved by treatment time adjustments.
Technical Library | 2018-01-17 22:47:02.0
Fine pitch copper (Cu) Pillar bump has been growing adoption in high performance and low-cost flip chip packages. Higher input/output (I/O) density and very fine pitch requirements are driving very small feature sizes such as small bump on a narrow pad or bond-on-lead (BOL) interconnection, while higher performance requirements are driving increased current densities, thus assembling such packages using a standard mass reflow (MR) process and maintaining its performance is a real and serious challenge. (...) In this study a comprehensive finding on the assembly challenges, package design, and reliability data will be published. Originally published in the SMTA International 2016
Technical Library | 2019-06-26 23:21:49.0
Copper-filled micro-vias are a key technology in high density interconnect (HDI) designs that have enabled increasing miniaturization and densification of printed circuit boards for the next generation of electronic products. Compared with standard plated through holes (PTHs) copper filled vias provide greater design flexibility, improved signal performance, and can potentially help reduce layer count, thus reducing cost. Considering these advantages, there are strong incentives to optimize the via filling process. This paper presents an innovative DC acid copper via fill formulation, for VCP (Vertical Continues Plating) applications which rapidly fills vias while minimizing surface plating.
Technical Library | 2021-06-15 15:11:43.0
Today's automated dispensing for electronics manufacturing is a complex and precise process in order to meet the challenges posed by ever more demanding assembly and component technology requirements. Dedicated dispenser technology is key to success in meeting challenging applications in a production environment with precision and repeatability. The major components that comprise a dispenser will be described, with a view toward understanding the importance of each; the result will illustrate how these sub-systems combine to create high-volume dispensing platforms. Real world examples with data substantiating the speed and accuracy obtained for some of the most common advanced dispensing applications in the market will be demonstrated such as high speed surface mount adhesive, wafer level Underfill and shield edge interconnects.
