Technical Library | 1999-08-27 09:29:49.0
Contract packaging houses have to contend with a large mix of die types and products. Flexibility and quick turnaround of package types is a must in this industry. Traditional methods of die encapsulation, (i.e., use of transfer-molding techniques), are only cost effective when producing a large number of components. Liquid encapsulants now provide similar levels of reliability1, and are cost effective...
Technical Library | 2019-05-21 17:23:47.0
Reflow temperature profiling is the most important aspect of proper control of the solder reflow process. It may appear to some to be a magical art practiced by a select experienced few, who are able to divine the proper settings for a reflow oven by reading graphs as if they were tea leaves. This does not have to be true. This article outlines a systematic method by which engineers and technicians can implement a successful reflow process from scratch.
Technical Library | 2019-07-05 09:33:05.0
Fourier Transform Infrared (FTIR) spectroscopy exists as one of the most powerful techniques for chemical identification and the most practical for “first step” analysis. Analytical instrumentation such as GC-MS and LC-MS are commonly used for identifying organic compounds. However, these techniques are costly and often require extensive set up time, method development, and sample alteration. Reliance upon FTIR as a robust and versatile tool can be based on its attributes of simplicity, speed, sensitivity, and affordability.
Technical Library | 2019-08-19 09:46:13.0
Boundary scan is a method for testing interconnects on printed circuit boards (PCBs) or sub-blocks inside an integrated circuit. It has rapidly become the technology of choice for building reliable high technology electronic products with a high degree of testability. Due to the low-cost and integrated circuit (IC) level access capabilities of boundary scan, its use has expanded beyond traditional board test applications into product design and service.
Technical Library | 2020-08-05 17:13:12.0
A primary issue in electronics reliability for military applications is the ability to ensure long term operability in harsh, extreme environments. This requires more rigid standards, such as the MIL-STD-883 (Department of Defense Test Method Standard for Microcircuits), which commercial grade electronics typically do not satisfy. A solution commonly employed is to package the critical electronic components in hermetically sealed metal or ceramic enclosures which are costly and labor intensive. Not only are the components more expensive, but the assembly process is more difficult to automate, resulting in a substantial cost premium for military grade electronics.
Technical Library | 2019-06-06 13:40:47.0
Legacy electronics assemblies, such as through-hole (Figure 1) and connectorized component packages, are robust and prevalent throughout industry. However, each of these assembly methods have reached their limits in terms of weight, volume, reliability, and most importantly cost. With cost reduction of assemblies now the primary focus area throughout the electronics industry, there is more of a need than ever to implement the latest advancements in surface mount technology (SMT) into electronics assembly designs. Although SMT has been utilized in the electronics industry for many years, implementation of the technology is still in the ever-evolving process of reducing component footprint size, component spacing, and component I/O pitch. Implementation of the most up-to-date SMT processes provides optimal weight, volume, and cost savings, for any type of assembly.
Technical Library | 2019-06-07 14:49:54.0
ACI Technologies was contacted in regards to poor solder joint reliability. The customer submitted an assembly that was exhibiting intermittent opens at multiple locations on a ball grid array (BGA) component. The assembly’s functionality did not survive international shipping, essentially shock and vibration failures, immediately making the quality of the solder joints suspect. The customer was asked about the contract manufacturer and the reflow oven profile as well as the solder paste and surface finish used. The ACI engineering staff evaluated the contract manufacturer’s technique and determined that they were competent in the methods they used for placing thermocouples in the proper locations and developing the reflow oven profile. The surface finish was unusual, but not unheard of, in that it was hard gold over hard nickel, rather than electroless nickel immersion gold (ENIG). The customer was able to supply boundary scan testing data which showed a diagonal row of troublesome BGA pins.
Technical Library | 2020-12-07 15:26:06.0
Temperature cycling testing is a method of accelerated life testing done to PCCs that are exposed to normal operation temperature variations over its lifetime. During the testing, intermittent "open" failures can first occur at the hot and cold extremes of the test, exposing weaknesses in the design and assembly. A poor/weak solder joint fatigues, a via trace or barrel cracks, loose connections or a component fails all causing an intermittent open. When not at extreme temperatures, the PCC assembly relaxes, the "open" closes creating electrical connectivity. If you are monitoring the PCC under test in-situ you will know that an intermittent failure has occurred, and the test could be stopped for inspection. If in-situ monitoring was not implemented, you would not know if there were intermittent failures or not. The PCC gets powered up and works fine at room temperature.
Technical Library | 2019-09-23 09:35:00.0
Failure analysis (FA), by its very nature, is needed only when things goawry. Before any testing is performed on the sample, a decision mustbe made as to whether or not the sample is allowed to be destroyedin the process of testing. Non-destructive testing can allow for re-use of the assembly since the functionality is not altered, but there still remains the possibility that inadvertent damage can occur through the course of the analysis. If non-destructive testing is preferred, then the following types of analysis can be performed. The testing can be divided into four categories: visual, X-ray (X-ray imaging and X-ray fluorescence), cleanliness (resistivity of solvent extract, ion chromatography, and Fourier transform infrared spectroscopy), and mechanical (non-destructive wire bond pull).
Technical Library | 2021-09-02 08:17:07.0
We are a professional manufacturer of PCB depaneling machines, which is workable for all boards, including flex and regid boards, v-scored boards and routed boards. Laser pcb depaneling is non-contact way without mechanical stress,this solution is good for modern precision PCB depaneling. It has below advantages: 1. No dust The production environment of the circuit board industry is carried out in the dust-free workshop. The traditional pcb depaneling equipment, such as blade moving type machine, will inevitably produce residues and micro powder, which will pollute the 10000 and 1000 class dust-free workshops and affect the conductivity of products. The UV laser PCB cutting machine is a vaporization processing process, which will not produce dust and is conducive to the conductivity of the product. 2. High cutting precision The processing gap of high-precision traditional processing equipment can not reach the gap width of less than 100 microns, which will cause certain damage to the lines on the edge or PCBA circuit board containing components. The focus spot of the laser cutting machine is small, and the ultraviolet cold processing mode has little thermal impact on the edge of the circuit board. The cutting position accuracy is less than 50 microns, and the cutting size accuracy is less than 30 microns, which will not affect the edge of the circuit board, and the precision is high. 3. No stress Traditional processing methods generally have V-grooves, which will cause certain damage to the board in the manufacturing process. The UV laser PCB cutting machine can directly cut the bare board without making V-grooves. In addition, the traditional processing methods directly use tools to act on the circuit board, especially the stamping method has a great impact on the circuit board, which is easy to cause board deformation. The laser cutting machine is a non-contact processing mode, which acts on the surface of the material through the high-energy beam, which will not cause the influence of stress and the deformation and damage of the circuit board. 4. For special-shaped cutting, it is easy to automate The UV laser PCB cutting machine can cut for any shape without replacing any props and fixtures, and without steel mesh. The same equipment can meet special-shaped and straight-line cutting, which is easy to realize assembly line automatic production and high flexibility. It is easy to improve production efficiency and save production process and production cycle. In particular, it can quickly and efficiently meet the needs of rapid proofing, directly import the drawing, and then locate the cutting. 5. High compatibility The UV laser PCB cutting machine can process the materials around the circuit board, such as PCB, FPC, covering film, pet, reinforcing board, IC, ultra-thin metal cutting, etc. it has strong practicability, is compatible with the processing of a variety of materials, is easy to operate, can be imported into the drawing, does not need to adjust any mechanical parts, and is easy to operate and maintain. 6. Good cutting edge effect The cutting edge is smooth and neat without burr. It can be processed and formed directly according to the size of the drawing, which is conducive to improving the yield of the product. It can be directly installed into the subsequent process without further processing. For more details about UV laser depaneling, please feel free to contact us. www.pcbdepanelingrouter.com
