Binary Gas Applications; continuous and non-continuous; corrosive and non-corrosive
Overview The D8254 is a programmable interval timer/counter, binary compatible with industry standard 82C54. The D8254 solves one of the most common problems in any micro-computer system, the generation of accurate time delays under software control
Electronics Forum | Sun May 22 23:34:53 EDT 2005 | thaqalain
What is equivalent binary number for 48 in an 8 bit LED display?
Electronics Forum | Mon May 23 09:18:43 EDT 2005 | dougt
48 decmial = 00110000 binary
Used SMT Equipment | In-Circuit Testers
The ATC-600A is a portable ramp test set designed to simulate the ground station or airborne environment needed to test Modes A and C transponders. The ATC-600A meets latest ARINC specifications and FAA regulations concerning transponder receiver sen
Used SMT Equipment | In-Circuit Testers
Aeroflex IFR ATC-600A The ATC-600A is a portable ramp test set designed to simulate the ground station or airborne environment needed to test Modes A and C transponders. The ATC-600A meets latest ARINC specifications and FAA regulations concernin
Industry News | 2020-09-25 03:54:45.0
SMTA is honored to announce Chidinma Imediegwu, a graduate student at the Georgia Institute of Technology, has been selected as the winner of the 2020 Charles Hutchins Educational Grant.
Industry News | 2021-06-01 06:01:48.0
Power Plant uses a certain power source to generate electrical power. The power plant control system controls the amount of fuel, water and air supplied to the boiler of the power plant, controls the start and stop of the plant and many other functions related to the power plant. This ensures that the power plant functions as intended with the highest efficiency.
Technical Library | 2013-10-17 17:46:01.0
Although several commercial and experimental Pb-free solder alloys are available as replacements for Sn-Pb solders, the following families of solders are of particular interest and are the prevailing choices of industry: eutectic Sn-Ag, eutectic Sn-Cu, eutectic Sn-Zn, eutectic Bi-Sn, and Sn–In. Since the properties of the binary Pb-free solders cannot fully meet the requirements for applications in electronic packaging, additional alloying elements are added to improve the performance of these alloys. Thus, ternary and even quaternary Pb-free solders have been developed, such as Sn-Ag-Cu, Sn-Ag-Bi, and Sn-Zn-Bi solder...
Technical Library | 2020-09-23 21:37:25.0
The need to minimise thermal damage to components and laminates, to reduce warpage-induced defects to BGA packages, and to save energy, is driving the electronics industry towards lower process temperatures. For soldering processes the only way that temperatures can be substantially reduced is by using solders with lower melting points. Because of constraints of toxicity, cost and performance, the number of alloys that can be used for electronics assembly is limited and the best prospects appear to be those based around the eutectic in the Bi-Sn system, which has a melting point of about 139°C. Experience so far indicates that such Bi-Sn alloys do not have the mechanical properties and microstructural stability necessary to deliver the reliability required for the mounting of BGA packages. Options for improving mechanical properties with alloying additions that do not also push the process temperature back over 200°C are limited. An alternative approach that maintains a low process temperature is to form a hybrid joint with a conventional solder ball reflowed with a Bi-Sn alloy paste. During reflow there is mixing of the ball and paste alloys but it has been found that to achieve the best reliability a proportion of the ball alloy has to be retained in the joint, particular in the part of the joint that is subjected to maximum shear stress in service, which is usually the area near the component side. The challenge is then to find a reproducible method for controlling the fraction of the joint thickness that remains as the original solder ball alloy. Empirical evidence indicates that for a particular combination of ball and paste alloys and reflow temperature the extent to which the ball alloy is consumed by mixing with the paste alloy is dependent on the volume of paste deposited on the pad. If this promising method of achieving lower process temperatures is to be implemented in mass production without compromising reliability it would be necessary to have a method of ensuring the optimum proportion of ball alloy left in the joint after reflow can be consistently maintained. In this paper the author explains how the volume of low melting point alloy paste that delivers the optimum proportion of retained ball alloy for a particular reflow temperature can be determined by reference to the phase diagrams of the ball and paste alloys. The example presented is based on the equilibrium phase diagram of the binary Bi-Sn system but the method could be applied to any combination of ball and paste alloys for which at least a partial phase diagram is available or could be easily determined.
Contact Us Sales manager: Mac Xie Mobile: +8618020714662(WhatsApp) Email: at@mooreplc.com Skype: +8618020714662 Contact Us ✭Product Overview✭ IMADYN D PM6, RAPID 64-BIT CPU MODULE WITH BINARY INPUTS, L AND C BUS The Siemens 6DD1600-0AK0 i
Contact Us Sales manager: Mac Xie Mobile: +8618020714662(WhatsApp) Email: at@mooreplc.com Skype: +8618020714662 Contact Us ✭Product Overview✭ FOR 2 AUTONOMOUS CONTINUOUS P-, PI-, PD- OR PID CONTROLLERS OR 4 ANALOG CONTROLLER OUTPUTS W. CO
Career Center | Muzzaffarnagar, India | Production
Complete programming of Pick & Place as per BOM. Working with both low & high Profile solder Paste, and Glue. Accurate Placement of all SMT Component like Chip, SOT, SOD, QFP, Tantalum Capacitor & etc. Familiar with the critical problem in process
| http://etasmt.com/cc?ID=te_news_industry,3561&url=_print
) solder is commonly used as lead finish material, which are deposited either by solder plating or solder coating. There are a number of reasons why the Sn/Pb binary system had become a popular choice as lead finish material
ASYMTEK Products | Nordson Electronics Solutions | https://www.nordson.com/en/divisions/yestech/products/automated-optical-inspection-systems/m1m-aoi
microscopes.Real-time color, normalized gray scale correlation,pattern matching and binary “blob”analysis are just a few of the tools used to automate the process. Nordson