Industry Directory | Manufacturer
2Layers - 18Layers ;HASL, OSP, Gold plating, immersion Gold/Silver/Tin, removable mask, gold-finger, carbon ink;Conact Person:Rene E-mail:rene@speedingcircuit.com Website:www.speedingcircuit.com
Industry Directory | Manufacturer
US manufacturer of metallized ceramic substrates & packages; specializing in PCTF (plated copper over thick film) & low cost AgENIG (silver with electroless nickel and immersion gold plating).
New Equipment | Soldering - Other
High specification, bench top rotary table soldering machine A versatile four station rotary bench top soldering machine, ideally suited for high or low volume production, the Quadron combines well proven pumped soldering techniques with advanced PL
New Equipment | Soldering - Other
High specification, bench top rotary table soldering machine A versatile four station rotary bench top soldering machine, ideally suited for high or low volume production, the Quadron combines well proven pumped soldering techniques with advanced PL
Electronics Forum | Mon Aug 16 13:18:46 EDT 2004 | davef
You bet our reponse changes. Q2R: Hard gold thickness is 4 to 10 u" for Au and 300 to 400 u" for nickel A2R: This is a hard gold spec?? It looks like a ENIG spec. Although, the Ni is quite heavy, 150 uin is sufficient for most applications. The gol
Electronics Forum | Thu May 30 08:04:25 EDT 2002 | zanolli
Hello Russ, I'm not quite sure I understand your question. Are you saying that you must hand solder these connectors because the gold plating doesn't allow other though hole processing methods to wet the solder the length of the pin in the PTH? Reg
Used SMT Equipment | In-Circuit Testers
SPEA 4060 Flying Probe Tester Recently serviced, currently in production becoming available soon. Only 12k hours of use. FOB: Origin Contact: AssuredTechnicalServiceLLC@Gmail.com Configuration: 4060 Manual Board Load * 4060 M - C
Used SMT Equipment | Bare Board Testers
SPEA 4060 Flying Probe Tester Recently OEM serviced, very low hours, currently in production becoming available soon. FOB: Origin Contact: AssuredTechnicalServiceLLC@Gmail.com Configuration: 4060 Manual Board Load * 4060 M - Configured System
Industry News | 2003-02-07 09:13:12.0
The Sessions Covered Current and Emerging Technologies
Industry News | 2003-05-19 10:06:43.0
The PCB is available with a maximum panel size of 406-by-460mm and a minimum board thickness of 0.8mm.
Parts & Supplies | Component Packaging
JUKI FX-1 laser E961172900 model:8010518 We supply JUKI laser(570/620/730/740/750/760/2010/2020/2030/2040/2050/2060/2070/2080/KJ-01/KJ-02//FX-1/FX-2/FX-3/3020R/JX-100 laser unit),YAMAHA laser,SAMSUNG laser,TENRYU laser,PHILIPS(ASSEMBLEON) FCM
Parts & Supplies | Pick and Place/Feeders
Supply original new and used JUKI Smt machine MNLA Lasers , And we also can support repair service 40045547 JUKI FX & 2070 LNC60 Laser JUKI 730 SENSOR E9631721000 JUKI 750 SENSOR E9631721000 JUKI 740 LA SENSOR(TOP CONNECTOR) E9636725000 JU
Technical Library | 2023-09-07 14:38:31.0
A repeat customer specializing in high-technology interconnect, sensor, and antenna solutions, partnered with us to dispense small volumes of solder paste (Indium 10.1 SAC305 T6SG 78%m) onto backplane connectors – gold pads 0.175mm x 0.225mm. We performed a test requiring 0.200mm diameter or smaller dots to demonstrate the dispensing capability required.
Technical Library | 2019-06-04 10:19:46.0
Interconnection technology relies very heavily on the ability of the conductors on a printed wiring assembly to maintain reliable signal integrity. Harsh environmental factors can precipitate a loss of conductivity due to oxidation and corrosion. Connections are typically soldered or inserted using pressure fitted connectors to obtain enough surface contact to meet the electrical conductivity requirements. In pressure contacts, surface integrity is especially critical where the abrasive effects of retraction and insertion can wear off the metallic finish from the contact area. This can expose the underlying copper or nickel and lead to increased resistance at the contact points. These types of conductors are frequently found in card edge connectors where the terminations are plated with a layer of nickel and gold (frequently referred to as gold fingers). A hard gold is typically used containing very small amounts of nickel and cobalt to increase the wear resistance.
Basics of soldering with EasyBraid's soldering tips
Events Calendar | Wed Apr 20 00:00:00 EDT 2022 - Wed Apr 20 00:00:00 EDT 2022 | ,
Virtual Course: Selection Criteria of Surface Finish for Next Generation PCB Technologies
Career Center | Dana Point, California USA | Sales/Marketing
We are currently seeking sales reps nationwide for this rapidly growing supplier of printed circuit boards (since 1986)with facilities in southern CA and eight PCB facilities in China and Taiwan, all ISO 9002 certified and UL94V-0 approved, some are
Career Center | Shen Zhen, China | Management,Sales/Marketing
Working in GLORYPCB for 10 years.knowing electronic supply chain very well. especially for PCB PCBA assembly and other Electronic Manufacturing Service.Glorypcb is a professional electronic manufacturer located in Shenzhen with three facilities.offe
Imagineering, Inc. | https://www.pcbnet.com/quote/board-quote-taiwan/
* Materials FR4(130Tg) FR4(170Tg) FR406(180Tg) Copper Weight 1 oz 2 oz 3 oz 4 oz Finish Plating ENIG1U" (Immersion Gold) ENIG2U" (Immersion Gold) ENIG3U" (Immersion Gold) ENIG4U" (Immersion Gold) ENIG5U" (Immersion Gold) Immersion Tin Immersion Silver HASL
PCB Libraries, Inc. | https://www.pcblibraries.com/forum/ipc-standards-for-manufacturing-assembly_topic877_post9030.html
and Flexible Adhesive Bonding Films IPC-4204 - Flexible Metal-Clad Dielectrics for Use in Fabrication of Flexible Printed Circuitry IPC-4552 - Specification for Eletroless Nickel/Immersion Gold (ENIG