New Equipment | Test Equipment
Fast and accurate ionic contamination cleanliness testing. Dynamic testing of ionic contamination is a widely approved and followed standard. So, too, is the equipment that makes it possible - SCS Ionograph®. Available in different models, the SCS
STI offers a variety of electrical test services from component-level testing/characterization to system-level testing. Electrical testing is offered to validate values in accordance with component manufacturer's performance specifications, a custom
Electronics Forum | Wed Sep 22 21:15:44 EDT 2021 | djenkins62
Hello Everyone: Heat Can Be Very Damaging to Boards and well as extended oven time can cut into valuable production time. Steel Camel is testing ambient temperature drying to remove diffused and embedded moisture in PCBs. We are seeking scrap pie
Electronics Forum | Thu Sep 23 15:49:45 EDT 2021 | stephendo
See if there are any board shops near you. One might provide scraps in exchange for name dropping.
Used SMT Equipment | Chipshooters / Chip Mounters
RS-1XL Features ▶Class leading speed, up to 42,000 cph. ▶0201* ~ 74mm×74mm / 50mm×150mm. ▶Wide component range. ▶Optimum line balance and highest throughput. ▶Newly developed "Takumi Head" with changing recognition sensor height. ▶JUKI's laser center
Used SMT Equipment | Chipshooters / Chip Mounters
RS-1XL Features ▶Class leading speed, up to 42,000 cph. ▶0201* ~ 74mm×74mm / 50mm×150mm. ▶Wide component range. ▶Optimum line balance and highest throughput. ▶Newly developed "Takumi Head" with changing recognition sensor height. ▶JUKI's laser center
Industry News | 2003-03-11 08:45:00.0
CAMtastic DXP is the latest version of Altium's complete CAM verification and editing system that bridges the gap between PCB design and manufacturing and facilitates communication between board designers, fabrication engineers, and their clients.
Industry News | 2019-03-10 20:30:11.0
The proliferation of tighter microvia densities and signal integrity requirements in printed boards within the electronics industry has revealed reliability concerns with microvia structures in high performance products. A number of IPC OEM member companies have approached IPC with examples of microvia failures in high-profile hardware that were not observed until after bare printed board fabrication, inspection and acceptance, including:
Parts & Supplies | Pick and Place/Feeders
Long board SMT Placement Machine JX-350 Chip 32,000CPH chip (Laser centering/Optimum) 21,000CPH chip (Laser centering / IPC9850) ■ From 0603 to □33.5mmsquare components ■ JUKI laser centering for high spe
Parts & Supplies | Pick and Place/Feeders
Starting in May 2008, JUKI Corporation (President Kazuyuki Nakamura; listed on First Section of the Tokyo Stock Exchange) is beginning worldwide sales of its High-speed Modular Mounter FX-3. The FX3 is an industrial robot for mounting electronic comp
Technical Library | 2017-07-13 16:16:27.0
Controlled humidity and temperature controlled surface insulation resistance (SIR) measurements of flux covered test vehicles, subject to a direct current (D.C.) bias voltage are recognized by a number of global standards organizations as the preferred method to determine if no clean solder paste and wave soldering flux residues are suitable for reliable electronic assemblies. The IPC, Japanese Industry Standard (JIS), Deutsches Institut fur Normung (DIN) and International Electrical Commission (IEC) all have industry reviewed standards using similar variations of this measurement. (...) This study will compare the results from testing two solder pastes using the IPC-J-STD-004B, IPC TM-650 2.6.3.7 surface insulation resistance test, and IPC TM-650 2.3.25 in an attempt to investigate the correlation of ROSE methods as predictors of electronic assembly electrical reliability.
Technical Library | 2018-11-29 13:43:54.0
Ionic contamination testing as a process control tool a newly developed testing protocol based on IPC-TM 650 2.3.25, was established to enable monitoring of ionic contamination within series production. The testing procedure was successfully implemented within the production of high reliability, safety critical electronic circuits, involving multiple production sites around the world. I will be shown in this paper that the test protocol is capable for meeting Six-Sigma-Criteria.
ACI Technologies Inc. (ACI) is a scientific research corporation dedicated to the advancement of electronics manufacturing processes and materials for The Department of Defense and industry. This video provides an overview of our commercial service
Offline Dual Table PCB Depaneling Router Machine with SycoTec Spindle 4025HY PCB Depaneling Router Features: 1. Two-slide PCB Separator 2. Low stress 3. Sharp cutting edge 4. Manul loading /unloading 5. High speed cutting by 4 axes control(XY
SMTnet Express, July 13, 2017, Subscribers: 30,584, Companies: 10,624, Users: 23,496 Divergence in Test Results Using IPC Standard SIR and Ionic Contamination Measurements K. Tellefsen, M. Holtzer, T. Cucu, M. Liberatore, M. Schmidt - Alpha
| https://www.eptac.com/blog/navigating-the-world-of-electronics-standards
. For instance, the IPC-6011 standard offers a generic performance specification for printed boards, ensuring that they meet rigorous quality and durability benchmarks
PCB Libraries, Inc. | https://www.pcblibraries.com/forum/cleanliness-test_topic1738_post7101.html
PCBA Cleanliness test process? For Ionic Residues on PCBA, there are three methods of testing in IPC-TM-650: Dynamic Extraction Methods, Static Extraction Methods and manual method
IPC is the trade association for the printed wiring board and electronics assembly industries.
Training Provider / Events Organizer / Association / Non-Profit
3000 Lakeside Drive, 309 S
Bannockburn, IL USA
Phone: 847-615-7100