Electronics Forum | Thu Apr 05 09:55:34 EDT 2018 | rob
The L Version is slightly bigger PCB handling capability. However, it's relative to Juki, not to other manufacturers. We have found that the extra large board Juki's are similar to our standard Yamahas. Don't know about the 760, but the 2060L is 41
Electronics Forum | Sat Apr 14 10:21:30 EDT 2007 | HOSS
We are processing a 5x22" PCB using Juki "2010E and 2060E". Machines are spec'd as 18x20" cabable. We just needed to adjust a conveyor sensor (1 time) and ignore a few placement area warnings.
Electronics Forum | Tue Jan 05 15:18:07 EST 2016 | g2garyg2
JUKI and PROMATION have teamed up for 48 inch long PCB production.
Electronics Forum | Tue Mar 19 07:04:21 EDT 2013 | Flux Capacitor
When I enter in the program data for a particular PCB on our Juki, I choose a board fiducial and enter its X Y location as the "bad mark position". (Although I'm not sure if your model refers to this as a "bad mark" as well.) Place a sticker over tha
Electronics Forum | Mon Jul 11 10:59:50 EDT 2016 | mnorthey
Other problems on previous machines that we have experienced is that there was not enough board support under the panel or that the panel thickness was inaccurate. Both situations can cause parts to bounce off the PCB or not to be pushed into the pas
Electronics Forum | Tue Jun 23 08:08:38 EDT 2009 | ptxems
We have a couple of Zeva/Juki PM570L's. One machine has developed a fault with the z axis motor. It is continually 'buzzing', we have checked and there is 24VAC on it. Although even on the other machine there is AC voltage on the motor. We have sw
Electronics Forum | Thu Oct 04 00:03:28 EDT 2018 | gaintstar
flason smt pick and place machine: http://www.flason-smt.com/product/Hanwha-IC-placer-SM321-High-Speed-SMT-Modular-Chip-Mounter.html http://www.flason-smt.com/product/Hanwha-Pick-and-Place-Machine-DECAN-F2-High-Speed-SMT-Modular-Chip-Mounter.html htt
Electronics Forum | Wed Jul 16 18:46:46 EDT 2008 | mariss
emti, Thank you for the reply but I'm looking for a reasonable quality pcb mfg. We do SMT and thru-hole in house (3 Juki KE-750L machines) of our product. My problem is with the bare boards: holes poorly registered with top copper, solder masks mis
Electronics Forum | Tue Sep 18 10:52:14 EDT 2012 | sarason
Sounds like a plan. The usual way is to count how many you use on the job either by pre-calculation. Or how many clicks the machine counts and save the data before switch off, then drop it back into a spread sheet. This depends very much on the mach
Electronics Forum | Tue Mar 06 04:58:58 EST 2018 | reckless
My wish would be to put 2-3 smaller 4 nozzle/7000cph desktop units and not in line saving me changeover time. Mostly because of the small real estate footprint. I can put one next to my office running 110V/350W - its small enough to fit on my desk
Products, services, training & consulting for the assembly, rework & repair of electronic assemblies. BGA process experts. Manufacturers Rep, Distributor & Service Provider for Seamark/Zhuomao and Shuttle Star BGA Rework Stations.
Training Provider / Manufacturer's Representative / Equipment Dealer / Broker / Auctions / Consultant / Service Provider
1750 Mitchell Ave.
Oroville, CA USA
Phone: (888) 406-2830
