Manufacturer of reed switches of 1W to 120W switching capability, and reed sensors of normally-open, normally-closed, and latching types for low level sensing.
Ruggedised electronic and fibre optic connectors and cable assemblies for demanding applications in medical, test & measurement, broadcast and industrial markets.
New Equipment | Board Handling - Storage
The F9001 quick adjust PCB Rack has been developed to provide a reasonably priced easy to adjust pcb carrier as an alternative to existing high priced products. The width of the rack can be quickly adjusted for different PCB sizes by unlocking the s
Manufacturer of reed switches of 1W to 120W switching capability, and reed sensors of normally-open, noramally-closed, and latching types for low level sensing.
Electronics Forum | Fri Sep 03 08:25:30 EDT 2010 | remullis
I removed the muffler yesterday and still had the latch releasing issue, the latch was tight, however the table had some play in it. I adjusted the play out of the table, setup table zero and it fixed the problem. Same symptom as if the latch were lo
Electronics Forum | Thu Sep 02 05:12:15 EDT 2004 | doi
I am using a triad connector and have problem with wetting at both connector latches.Observed that the leads have very good shiny wetting however concerning the latches the solder just seem to disappear to thin airafter reflow.The connector has a gui
Used SMT Equipment | In-Circuit Testers
Agilent 6674A DC Power Supply 60V/35A The Agilent 6674A model is part of the 667x series of 2000 Watt, single output, power supplies, with an internal GPIB interface and SCPI programming. These models provide many talker/listener functio
Used SMT Equipment | In-Circuit Testers
HP / Agilent 6675A Power Supply 120V, 18A, GPIB Low-noise output Linear output regulation on 200 & 500 W models Overvoltage & overcurrent protection Fast up & down programming Auto-parallel and series operation GPIB (SCPI) on 66xA models Measured V &
Industry News | 2003-02-20 08:04:10.0
The Mini-Fix card-to-cable connector is designed to withstand hundreds of mating cycles with high contact security and mechanical stability.
Industry News | 2018-06-14 12:10:52.0
Now available from FKN Systek, Stackable PCB Transport and Storage Racks made of conductive material for safe and convenient handling of Printed Circuit Cards during assembly. These Racks will hold up to 50 PCBs from 2” to 9.8” (5 to 25 cm) wide. Racks are made of conductive plastic temperature rated to 176 O F, Surface resistance
Technical Library | 2001-04-24 10:41:53.0
Tau models describe the timing and functional information of component interfaces. Timing information specifies the delay in placing values on output signals and the timing constraints (set-up/hold, pulse-width) on input signals of a component. Functional information, through a finite state machine (FSM), specifies when output signal values change, when input signal values are latched, and how output values are determined as a function of input values.
Technical Library | 2012-12-14 14:28:20.0
This paper examines the potential failure mechanisms that can damage modern lowvoltage CMOS devices and their relationship to electrical testing. Failure mechanisms such as electrostatic discharge (ESD), CMOS latch-up, and transistor gate oxide degradation can occur as a result of electrical over-voltage stress (EOS). In this paper, EOS due to electrical testing is examined and an experiment is conducted using pulsed voltage waveforms corresponding to conditions encountered during in-circuit electrical testing. Experimental results indicate a correlation between amplitude and duration of the pulse waveform and device degradation due to one or more of the failure mechanisms.
we have many hitachi equipment and hitachi feeders to sell . if you want to know more , please contact us tina@smtfeeders.cn
we have many universal gold plus feeders to sell . www.smt-store.com
| https://www.eptac.com/webinars/assembly-understanding-the-hardware-side-of-ipc-a-610
. There is a lot more that goes into an assembly than just soldered connections. This HARD(ware) from the board, screws, wire, handles, latched, heat sinks and formed components all have criteria that must be met by IPC-A-610 too
