Electronics Forum | Thu Oct 11 17:44:30 EDT 2001 | aaelect
OK, OK. 672 ball BGA. The pcbs are PC Card bus size and are .015 thick. There are 3 on a panel with about 1/2" between and rails. The aluminum plates are about 3" by 7". There are 3 cutouts which allow for the parts from either side to protrude du
Electronics Forum | Mon Jun 29 13:51:29 EDT 1998 | Russ Miculich
| WHAT SHOULD THE RATIO BE OF STENCIL APERATURE TO PAD TO GET GOOD QUALITY RESULTS. BY THAT I MEAN, A MINIMM OF SOLDER BALLS, AND LITTLE TO NO BRIDGING, SHORTS, ETC.. | RIGHT NOW WE ARE USING A 1:1 RATIO, BUT ARE INVESTIGATING REDUCING THE APERATU
Electronics Forum | Mon Jun 29 13:50:48 EDT 1998 | Russ Miculich
| WHAT SHOULD THE RATIO BE OF STENCIL APERATURE TO PAD TO GET GOOD QUALITY RESULTS. BY THAT I MEAN, A MINIMM OF SOLDER BALLS, AND LITTLE TO NO BRIDGING, SHORTS, ETC.. | RIGHT NOW WE ARE USING A 1:1 RATIO, BUT ARE INVESTIGATING REDUCING THE APERATU
Electronics Forum | Mon Jun 15 06:21:13 EDT 2020 | ameenullakhan
Hi Team, Main reason for HIP are; 1. Warpage in component or PCB : Verified the part and PCB 1.6 mm thickness no warpage found. 2. Hip was at different locations : center as well as corner : So not because of warpage of component. 3.Solder paste equ
Electronics Forum | Wed Sep 22 22:23:55 EDT 1999 | SY
| | | | | My stencil thickness is 6 mil and we got qfp's with fine pitch. | | | | | how many percent should i reduce my stencil aperture using a 6 mil stencil for 0.5 mm pitch and 0.4 mm pitch ? | | | | | | | | | | thanks | | | | | | | | | We use 6
Electronics Forum | Wed Sep 22 21:23:03 EDT 1999 | se
| | I've had some trouble pasting a test board for a MicroBGA trial. Most of the paste remains in the stencil apertures. | | The stencil is 6 mil thick, laser cut and electo-polished. | | The apertures are 12 mil in diameter with 20 mil pitch. | | We
Electronics Forum | Thu Sep 23 12:47:48 EDT 1999 | Earl Moon
| | | I've had some trouble pasting a test board for a MicroBGA trial. Most of the paste remains in the stencil apertures. | | | The stencil is 6 mil thick, laser cut and electo-polished. | | | The apertures are 12 mil in diameter with 20 mil pitch.
Electronics Forum | Wed Dec 07 16:01:45 EST 2005 | JP
I am attempting to reball some PBGA's with no luck. The problem is getting the solder spheres to sit in the stencil apertures and removing excess spheres. I apply light amount of flux to pads of a BGA, align a stencil over a BGA, then pour solder s
Electronics Forum | Sat Sep 23 15:13:40 EDT 2000 | Francois Racine
Hi Sophia, I`m responsible of SMT line and we solved this problem with a complete automatic solder paste printer machine. In the past we had problem with off alignment and solder height too.... at that time we used a semi-auto printer machine and w
Electronics Forum | Tue Nov 11 09:19:17 EST 2008 | davef
By the way you asked the question, we assume that by "reballing" you mean bumping, we should be able to figure that out: * Volume of the ball = ( pi*d^�)/6 = [355/113] *0.6*0.6*0.6]/6 = 0.11mm^3 * Volume of solder required = 2*volume of ball = 2*0.11
