1132 electrovert omniflo 10 reflow oven jmw results

Full Site - : electrovert omniflo 10 reflow oven jmw (Page 9 of 39)

Reflow oven

Electronics Forum | Fri Oct 27 09:42:12 EDT 2000 | Daniel Carlsson

I wonder if anyone have experience from using a fairly new reflow oven and would like to share your toughts (advantages or disadvantages) with me. I�m especially interested in: Conceptronic, Electrovert, ERSA, Heller, Quad, Rehm, Seho, SMT or Vitroni

Reflow oven

Electronics Forum | Fri Jun 26 10:33:08 EDT 2015 | Asif

Hello Professionals, Good morning, We are circuit card manufacturer for the Aerospace industry with low volume and High mix level. We have a plan to Purchase a NEW REFLOW OVEN. Currently we are using Electrovert BRAVO reflow oven which is about 8 yea

Reflow oven reliability?

Electronics Forum | Wed Sep 12 11:10:40 EDT 2012 | cyber_wolf

We run BTU, Vitronics and Electrovert. All of those are rock solid machines AS LONG AS YOU KEEP THEM PM'ed. For some reason companies seem to neglect their oven PM's. Make sure you are buying an air only oven if you aren’t running nitrogen. The flux

Double-sided reflow process.

Electronics Forum | Thu Oct 08 22:32:53 EDT 1998 | E.

*Reply to: ericr@nj.tanon.com Without going into a lengthy explaination {at this time}, has anyone experimented, tested, evaluate, and/or 'perfected' an SMT double-side reflow process. Presently I'm using a Kester R593 OA (water soluble) Sn63/Pb37 -

Re: Double-sided reflow process.

Electronics Forum | Sat Oct 10 04:58:18 EDT 1998 | Tony B

| *Reply to: ericr@nj.tanon.com | | Without going into a lengthy explaination {at this time}, has anyone experimented, tested, evaluate, and/or 'perfected' an SMT double-side reflow process. Presently I'm using a Kester R593 OA (water soluble) Sn63/

Electrovert Omniflo 7 reflow ovens

Electronics Forum | Thu Aug 30 13:22:47 EDT 2001 | arzu

180deg More important are the preheat and soakzones and temp ramps. How to check: I used to do it as follows: use a TEST-PCB with fixed thermocouples and connect it to the mole. Print the profile on transparant paper. do it again e.g. each week and

Electrovert Omniflo 7 reflow ovens

Electronics Forum | Thu Aug 30 11:59:00 EDT 2001 | Spanky

Hey all, I have 3 questions about reflow. Hopefully someone can help me. 1. I am having a problem. I set the peak at 230 and my mole thermocouples are telling me the temp in that zone gets to 237. How is this possible even if the thermocouple

Non-wetting: PTH on double-side reflow

Electronics Forum | Wed Apr 06 11:10:47 EDT 2005 | smt_rookie

We process a double-side reflow board (10 ups). Chips and IC's on the bottom side while chips, IC's plus thru-hole connectors and IC sockets on top side (bottom side first then top side reflow). In the past, we were not encountering any soldering pro

Electrovert OmniFlo Ovens

Electronics Forum | Wed Feb 09 10:19:19 EST 2005 | pjc

According to one of Electrovert's reflow engineers, hour meters have not been installed "for quite some time". So, I stand corrected, older OmniFlo series ovens may have hour meters.

Electrovert Omniflo-7 Reflow Oven VS Lead-Free

Electronics Forum | Thu Feb 10 09:25:44 EST 2005 | lyrtech

Hi, Actually we're looking for a new reflow oven regarding lead-free process and higher capacity production. We have an opportunity for a second hand Electrovert Omniflo-7 (nitrous ready) that respect our budget. My questions are: Does anyone ha