Technical Library | 2007-01-03 16:36:58.0
Solder paste dispensing is not a new process. However, today's microelectronics present a daunting array of technical challenges to meet deposit size requirements. The need for better paste formulations, more precise equipment, and more tightly controlled processes is driving paste suppliers and equipment suppliers to develop new methods and materials. The most challenging solder paste deposits are those smaller than 0.25mm in diameter and today’s electronics demand such deposits. This paper addresses the process requirements for solder paste micro-deposits in terms of material, equipment and process variable control required for success in producing 0.25mm and smaller deposits.
Technical Library | 2008-12-11 01:15:56.0
Flame retardants have been around since the Egyptians and Romans used alum to reduce the flammability of wood. Brominated flame retardants (BFRs) first experienced use after World War II as the substitution of wood and metal for plastics and foams resulted in materials that were much more flammable. The widespread use of BFRs initiated in the 1970s with the explosion of electronics and electrical equipment and housings. For the US market, all of these products must conform to the UL 94 flammability testing specifications. In fact, the most common printed circuit board (PCB) in the electronics industry, FR-4, is defined by its structure (glass fiber in an epoxy matrix) and its compliance to UL 94 V0 standard.
Technical Library | 2009-11-18 23:37:52.0
Accurate component placement is a basic requirement for any pick and place machine. The first step towards accurate placement is accurate centering, or measurement of the component’s position on the placement head. One of the most widely used centering methods for ICs, connectors, and odd‐shaped components are a camera based system that measures the component position relative to a known point. Camera based centering systems include three main elements: lighting, camera, and software. Each of these elements are critical to obtaining an accurate measurement of the component and ultimately for accurate component placement on the PCB. As the old adage goes, the system is only as strong as its weakest link.
Technical Library | 2013-04-12 07:31:31.0
As change is inevitable, therefore so is obsolescence. In the electronics sector, stocks of components used in subassemblies will eventually run out, no surprise there! However on many occasions, particularly in the often long product life cycles associated with the traditional UK OEM’s in the industrial, military and medical sectors, to name but three, component supply gets ‘difficult’ long before the customers products themselves reach their ‘end of life’. Component manufacturers work to a commercial agenda; when the popularity of a specific device wanes, or indeed when new features are demanded by the market, they will cease production and redeploy their manufacturing capacity to devices that are being demanded by their high volume customers; the global players.
Technical Library | 2013-11-27 16:54:01.0
The need in complexity for microwave space products such as active BFNs (Beam Forming Networks) is increasing, with a significantly growing number of amplitude / phase control points (number of beams * numbers of radiating elements). As a consequence, the RF component’s package topology is evolving (larger number of I/Os, interconnections densification ...) which directly affect the routing and architecture of the multilayer boards they are mounted on. It then becomes necessary to improve the density of these boards (...) This paper will present the work performed to achieve LCP-based high density multilayer structures, describing the different electrical and technological breadboards manufactured and tested and presenting the results obtained.
Technical Library | 2015-03-12 18:26:16.0
Miniaturization and the integration of a growing number of functions in portable electronic devices require an extremely high packaging density for the active and passive components. There are many ways to increase the packaging density and a few examples would be to stack them with Package on Package (PoP), fine pitch CSP's, 01005 and last but not least reduced component to component spacing for active and passive components (...)This paper will discuss different layouts, assembly and material selections to reduce component to component spacing down to 100-125um (4-5mil) from today’s mainstream of 150-200um (6-8mil) component to component spacing.
Technical Library | 2017-03-22 20:58:08.0
Water soluble lead-free solder paste is widely used in today’s SMT processes, but the industry is slowly moving away from water soluble solder pastes in favor of no-clean solder pastes. This shift in usage of solder paste is driven by an effort to eliminate the water wash process. Some components cannot tolerate water wash and elimination of water washing streamlines the SMT process. Despite this shift, certain applications lend themselves to the use of water soluble solder paste.This paper details the research and development of a new water soluble lead-free solder paste which improves on the performance characteristics of existing technologies.
Technical Library | 2019-04-07 22:47:46.0
How to protect your PCB from moisture related damage? J-STD-033 put forward stricter regulation on the MSD exposure environment,when the exposure time exceed the tolerated,the moisture will penetrate into electronics,Moreover, the newest RoHS regulation will rise soldering temperature,the sudden high temperature will lead to expansion and cracking on electronic components. In order to decrease the moisture defect on PCB for the manufacturers in China,Climatest Symor® begin to concentrated on electronic dry cabinet R&D since early 1990s,we specialize in handling temperature and humidity for 20 years,and we provide best solution for PCB storage.
Technical Library | 2016-08-17 01:24:36.0
To stake a claim in upcoming new technologies and increasing improved customer experience, it is now becoming a central point of consideration to bring out the new classy vehicle design, car manufacturing techniques, testing system in the global market. The current vehicle manufacturer’s also aim to maintain equilibrium between deep capital investment and long product cycle to make the car model a success story. With this, the type of printed circuit board to be used in the vehicle is decided with focusing more on the type of material used in the vehicle and the level of electronic manufacturing and design solution needed in the vehicle production. To go into the roots of the automotive industry, it is equally important to get insights into the PCB used in vehicles and the new innovations brought forward by researchers to create a dream vehicle of the series. The below paragraph drives you to the types of PCB used in the automotive sector.
Technical Library | 2013-04-12 07:22:40.0
Here Chris talks about the pitfalls, the paucity of safe options for manufacturers seeking rare components, and his exasperation with organisations that appear to shelve common sense at the first sign of a shortage. He shares his ‘no nonsense’ approach to getting things right first time, and explains his thinking in establishing an independent distributor focused exclusively on delivering 100% component integrity.
