Custom AC/DC Resistive Load Bank solutions built in a timely and cost effective manner to our customer's exact specifications from 25W to 30KW in a single chassis. Three of our 30KW chassis can be integrated to create a 90KW load.
Ohm's law wristwatches, desk clocks and wall clocks for DC or AC applications, with unique resistor band color chart. Handy for any electronics professional, student or hobbyist.
New Equipment | Cable & Wire Harness Equipment
Threaded stainless steel tube NTC thermistor temperature sensor probe for temperature measurement of liquid, water, air, etc. Ideal for vessel and pipe installation. Typical application coffee maker, tea kettle, water heater boilers, soybean milk coo
Radial Resin Bead NTC Thermistor Temperature Sensor is polycrystalline mixed oxide ceramics made semiconductor type NTC Thermistor chip soldered with radial metal wire, coated with epoxy resin bead, for temperature measurement range -45C to +125C.
Electronics Forum | Mon Sep 18 14:43:06 EDT 2006 | jdengler
Steve, I don't think it was a Yageo if the value is 10 ohms. Yageo would label them as 10R0 for 10 ohms. 1002 would be a 10K ohm resistor. Jerry
Electronics Forum | Tue May 07 15:30:41 EDT 2013 | bobpan
your card is probably bad.....you can ohm out the motor and cable if you want... z motor windings 1.36 ohms z motor cable and windings 1.82 ohms good luck
Used SMT Equipment | General Purpose Test & Measurement
Specifications: Number of Channels - 2 AMPLITUDE RANGE - MAX 1.25Vp-p into 50ohm AMPLITUDE RANGE - MIN .03Vp-p into 50ohm STANDARD MEMORY/RECORD LENGTH
Used SMT Equipment | In-Circuit Testers
Agilent 8714ES RF Network Analyzer (S-parameter), 300 kHz to 3 GHz The Agilent 8714ES features an S-parameter test set with full two-port vector-error correction, providing complete and accurate measurements of device S-parameters. Two independ
Industry News | 2003-03-20 08:12:57.0
Nichicon has increased the top capacitance value of its WG series of surface mount electrolytic capacitors from 1000 to 1500uF.
Industry News | 2003-04-22 09:33:13.0
Honda Connectors has released its first Infiniband I/O connectors, designed for easy assembly in high-speed differential signal applications.
Parts & Supplies | Pick and Place/Feeders
BNC-FINAL RESISTOR 50 OHM
Technical Library | 2023-06-02 14:13:02.0
This work examines the use of dual-material fused filament fabrication for 3D printing electronic componentsand circuits with conductive thermoplastic filaments. The resistivity of traces printed fromconductive thermoplastic filaments made with carbon-black, graphene, and copper as conductive fillerswas found to be 12, 0.78, and 0.014 ohm cm, respectively, enabling the creation of resistors with valuesspanning 3 orders of magnitude. The carbon black and graphene filaments were brittle and fracturedeasily, but the copper-based filament could be bent at least 500 times with little change in its resistance.Impedance measurements made on the thermoplastic filaments demonstrate that the copper-based filamenthad an impedance similar to a copper PCB trace at frequencies greater than 1 MHz. Dual material3D printing was used to fabricate a variety of inductors and capacitors with properties that could bepredictably tuned by modifying either the geometry of the components, or the materials used to fabricatethe components. These resistors, capacitors, and inductors were combined to create a fully 3Dprinted high-pass filter with properties comparable to its conventional counterparts. The relatively lowimpedance of the copper-based filament enabled its use for 3D printing of a receiver coil for wirelesspower transfer. We also demonstrate the ability to embed and connect surface mounted components in3D printed objects with a low-cost ($1000 in parts), open source dual-material 3D printer. This work thusdemonstrates the potential for FFF 3D printing to create complex, three-dimensional circuits composedof either embedded or fully-printed electronic components.
03027548-01 Guide, left-hand side 03027563-01 Loctite 7063 CLEANER 03027570-03 HOTLINK CARD CPCI A14 K-01 03027644-01 HOLDER FOR CABLE INTERFACE 03027646-02 JUMPER 120 Ohm SUD-D PIN 03027905-01 Adapter cable MTC2 CAN bus 03028249-02 Pneumatic S
Contact Us Sales manager: Mac Xie Mobile: +8618020714662(WhatsApp) Email: at@mooreplc.com Skype: +8618020714662 Contact Us ✭Product Overview✭ Brand GE Fanuc Series VersaMax Manufacturer GE Intelligent Platforms (Former); Emerson Automati
Career Center | Houston, Texas USA | Engineering,Management,Quality Control,Technical Support
Seasoned Process & Quality Engineer. Degreed Chemical Engineer. 20+ years in Electronics Semiconductor manufacturing. Proficient in Quality Statistical tools, Design of Experiments, FMEAs, APQP, PPAP, ISO 9000, ISO/TS 16949 etc.
Career Center | Colton, California USA | Engineering,Maintenance,Production,Quality Control,Research and Development,Technical Support
• Strong experience with the installation, training, and repair on a variety of electro-mechanical, pneumatic, PLC, or computer controlled systems. • Strong Knowledge in SMT equipment, Screen Printer, AOI/SPI, Conformal Coat Systems, Reflow oven, X-R
| https://www.wesource.com/test-and-measurement-equipment/hp-35678a-50-ohm-type-n-calibration-kit-id-53603/
HP 35678A 50 Ohm Type N Calibration Kit ID_53603: World Equipment Source COMPANY PROFILE FINDER'S PROGRAM R1-Surplus Wesource159 CALL US
KingFei SMT Tech | https://www.smtspare-parts.com/sale-9235586-ohm-meter-smt-spare-parts-resistance-tester-for-e-cigarette-510-thread-rda-rba-diy-vaporizer.html
OHM meter SMT Spare Parts , Resistance Tester for E Cigarette 510 Thread RDA RBA DIY vaporizer Leave a Message We will call you back soon