Electronics Forum | Thu Jan 29 14:24:56 EST 2004 | rick
What kind of cleaning method you recommend for PCB - double side SMD (fine pitch and BGA components) and THT elements (PCB are for microwave application!!). Process technology no-clean.We have to remove grease-fingerprints, dust etc. It is low volume
Electronics Forum | Mon Mar 25 21:50:10 EST 2002 | davef
Some of this was copped from Fred. There are numerous package types that now fall under the rubric of land grid array [LGA]. Land grid devices [ie, Bumped Chip Carrier� [BCC], LGA, Quad Flat-pack No-lead [QFN], MicroLeadFrame�, etc] are essentially
Electronics Forum | Fri Sep 14 02:18:32 EDT 2001 | gsparka
Hi. After reflow soldering. There are lots of non wetting of leads. 71 b'd all are mounted resister,condensor,qfp,plcc,bga have got the defects so many. all defecs occured in the fine pitch ic. others are good. On some fine pitch pads not mou
Electronics Forum | Thu Feb 08 08:28:11 EST 2007 | mzaboogie
Good Morning Everyone, We have an application coming up with several BGA's on a RoHS assembly. One is a 25 mil ball on a 40 mil pitch, another is a 15 mil ball on a 40 mil pitch. In the past for leaded assemblies, we have used square apertures for 1
Electronics Forum | Tue Jul 27 16:08:04 EDT 1999 | Kathleen at ATL
I'm working on a prototype board that requires a 600 pin BGA. This is a metal top BGA being placed on a 11" x 17" PCB about .62" thick. The part is 1.77" square with a 50 mil pitch and 30 mil bump diameter. The bumps are located on the perime
Electronics Forum | Wed Oct 30 15:50:39 EST 2002 | dphilbrick
Dan Generally it is a good practice. If we are doing PTH type assembly or "low end" assembly I would probably not worry, but many board finishes today such as white tin, gold and OSP mandate special handling. Oils from dirty hands can cause solderin
Electronics Forum | Fri Mar 07 03:37:26 EST 2003 | emeto
Hi Ygwie, My experience shows there is not unique answer.Actually it depends on design,printing reflow or wave.It might be top side with lesser cmps.Top side might have fine pitch or BGA or CSP,LLGA ....,so you have better planarity when the PCB is b
Electronics Forum | Wed May 29 17:17:49 EDT 2002 | wilcoxito
As far as aperture dimensions go, I found a technical note written by Micron that recommends using "square apertures with sides equal in length to the diameter of the PCB pad. The corners of the square should also be slightly rounded, and the apertu
Electronics Forum | Tue Sep 01 19:31:36 EDT 1998 | Kallol Chakraborty
| We are experiencing shorting on a BGA. The part has a 1mm pitch with a 196 I/O count. The problem seems to pop up without warning & disappear in the same manner. | Our pad design is .020" diameter pads with .025" solder resist diameter. The ce
Electronics Forum | Fri Jan 16 07:06:47 EST 2004 | Mika
Component manufacturer often have recommendation for pad layout and process setup. This should be used as a guideline to help You to set up the process. Exactly what type of component is this, uBGA? We populate 64 I/O uBGA's on our pcb's with 0.3 mm
Products, services, training & consulting for the assembly, rework & repair of electronic assemblies. BGA process experts. Manufacturers Rep, Distributor & Service Provider for Seamark/Zhuomao and Shuttle Star BGA Rework Stations.
Training Provider / Manufacturer's Representative / Equipment Dealer / Broker / Auctions / Consultant / Service Provider
1750 Mitchell Ave.
Oroville, CA USA
Phone: (888) 406-2830