Electronics Forum: conformal coat ribbon (Page 1 of 105)

Bubbles in conformal coat

Electronics Forum | Thu Aug 27 11:35:07 EDT 2009 | davef

There are many possibilities: * Conformal coat is incompatible with surface residue on the board * Conformal coat is incompatible with solder mask on the board * Moisture is out-gassing from the board * Conformal coat is too thick and does not allow

Bubbles in conformal coat

Electronics Forum | Thu Aug 27 08:34:50 EDT 2009 | floydf

I am having trouble with little air bubbles in my conformal coat. It ranges from a few pin sized bubble to looking like spit. We are using Dow 2620 silicone conformal coat applied with a PVA sprayer machine. The conformal coat comes in bladder bags t

Bubbles in conformal coat

Electronics Forum | Fri Oct 09 16:07:30 EDT 2009 | dlabelle

We use Dow 2620 silicone conformal coat applied with PVA1000 sprayer machine. If used on a daily bases, we have no problem. If we let the machine sit idle for over a week, we will get bubbles in the conformal coating. Sometimes, purging the line w

Cleaning for conformal coat

Electronics Forum | Mon Jan 28 11:50:23 EST 2013 | johng

Good morning Mark, No issues around the masking at this point. The issue seem to be in open areas as well as between clad runs. We are using Humiseal 1A33 Conformal Coat.

Cleaning for conformal coat

Electronics Forum | Fri Jan 25 12:23:07 EST 2013 | dontfeedphils

By "they've been through the wash cycle twice" what do you mean? What kind of cleaning process do you use? What sort of chemistry? How do you handle the assemblies after wash and before coating? Do the operators where power free gloves? -Phil

Cleaning for conformal coat

Electronics Forum | Fri Jan 25 12:14:18 EST 2013 | johng

I'm using urethane conformal coat and have fisheyes and dewetting after coating even though the PWAs have been through the wash cycle twice. I'm looking at using Ionox 13302 in an ultrasonic cleaner as a short term solution until root cause can be id

Cleaning for conformal coat

Electronics Forum | Fri Jan 25 12:15:04 EST 2013 | johng

I'm using urethane conformal coat and have fisheyes and dewetting after coating even though the PWAs have been through the wash cycle twice. I'm looking at using Ionox 13302 in an ultrasonic cleaner as a short term solution until root cause can be id

Bubbles in conformal coat

Electronics Forum | Thu Sep 10 15:01:28 EDT 2009 | mefloump

I currently spray DOW 2620 with my PVA650 without any problems. I do not thin it but I do have a distance between the coating machine and IR oven to provide a flash off period. I notice bubbles only when the flash off time is too short and the coatin

Bubbles in conformal coat

Electronics Forum | Wed Sep 02 11:36:22 EDT 2009 | kpm135

Is this an established process that is just now exhibiting these problems, or is this a brand new process you're just setting up? What is the rest of your process like? What is done to the boards before you coat them? Water washed? Solvent washed? Sa

Cleaning for conformal coat

Electronics Forum | Mon Jan 28 08:44:21 EST 2013 | diamondmt

John, In addtion to the cleaning process you may wnat to look at the masking materials you are using as well. Are you using any temporary masking tape? If so, do the dewetted areas coincide? Some of these tapes use a silicone-based adhesive which wi

  1 2 3 4 5 6 7 8 9 10 Next

conformal coat ribbon searches for Companies, Equipment, Machines, Suppliers & Information

Dispenser Pumps

World's Best Reflow Oven Customizable for Unique Applications
High Precision SMT Fluid Dispensers

MSD Dry Cabinets
Jet Printing and Cleaning Challenges

PCB Assembly Supplies - ONLINE STORE
Your 2021 IPC Training Schedule

Inspection mirrors for electronic rework and repair.
PCB Depanelizers

ONLINE IPC Training & Certification