Electronics Forum | Sat Feb 25 12:01:28 EST 2017 | ttheis
I'm setting up a asymtek millenium m-cob style dispenser for the first time and running through the master offsets routine but when it attempts to find the needle in the nsz needle sensor it works in the x direction but when it attempts to locate in
Electronics Forum | Mon May 14 04:00:15 EDT 2018 | sarah2018
Before you buy glue dispensing machine, you need tell the supplier two question as below: Two questions before purchase 1.What’s type of glue do you use ? What’s the base characteristic ? A)One-component or two-component (A&B glue)； B)What is the A
Electronics Forum | Fri Mar 10 11:29:46 EST 2017 | mmjm_1099
What part of the country are you located? I know numerous stencil manufacturers in the country that I could refer you to. The one we currently use is Stentech and guarantee next day delivery for basic laser cut stencils. They have always kept their w
Electronics Forum | Tue May 01 20:40:38 EDT 2018 | sarason
In the past I have worked on 600 Amp FET Blocks. The rule was no voids. The circuit board would be heavy copper. 4 times normal plating time. Not particularly high resolution on the board say 20 mils. To help with the heavy plating. The boards were t
Electronics Forum | Wed Mar 15 13:35:40 EDT 2017 | scotceltic
I have a double sided PCBA setup. I have MSL components on both assembly sides. When I run Assy Side one I am within the allotted hours remaining on the MSL component. I then wait 40 hours before running 2nd Assy side. By then the hours on the 1s
Electronics Forum | Fri Nov 03 11:30:29 EDT 2017 | davef
regarding dwl comment, "For low volume hand assembly, deionized water or IPA should work fine." Deionized water: Deionized water is corrosive. It needs to be removed. Proof? Drop a copper coin into a covered jar of DI water and watch what happens ov
Electronics Forum | Thu Mar 30 10:02:03 EDT 2017 | Bestglobal SMT
We have a 2008 DEK horizon 03i this machine has been a very reliable system. we are having an issue with the print being offset in the x .2mm I have run 4 different boards - same issue on all. same offset. i can print the board 10 times over and
Electronics Forum | Tue Apr 18 07:46:30 EDT 2017 | pavel_murtishev
Dear PCBFOX, I use CAM350 v12.2 build 1135. I am trying to use CAM350 DFMStream module for paste mask layer check. Examination I am interested in most of all is "Paste Mask Layer Check - Missing Paste Mask on SMD Pads (MP)", i.e. missing stencil ape
Electronics Forum | Tue Apr 11 13:01:36 EDT 2017 | mrich208
Yes Sir, someone had replaced the fuse with a resistor and it had burned up. We had an exact board on the VCD. We swapped them and it worked! I am not sure how this forum works but now the machine will zero and say it's missing a part but the sequ
Electronics Forum | Wed Apr 19 10:48:36 EDT 2017 | robl
Thanks for the suggestion Rob, this might work > for us in some cases. In most cases though, I'll > need multiple coupons per PCB purchase (a coupon > per coating "setup"). > > Currently talking to > some PCB suppliers to see if anyone can of
Manufacturer of PCB depaneling and PCB soldering machines since 2005, products include CE approval V-groove PCB depanelizer, PCB router, PCB punching machine, laser depaneling, hot bar soldering machines and soldering robots.
Liwu Industrial Park, Yuanzhou Town, Boluo
Huizhou, 30 China
Phone: +86-138-29839112
