parameters

"parameters" search results in the Electronics Forums



944 results found for "parameters" in the Electronics Forums

Order by: Relevancy |   Date

solder ball

Jan 2, 2020 | It is strange that you're having issues while using the same process parameters (including stencil)

Mydata My9

Oct 18, 2019 | 3 different A12 tools and the same error could be a problem with the tool holder or a parameter. I s

Juki / Zevatech 730/740 - MS Parameters window

Apr 30, 2019 | Caro amigo Charlien poderia me dizer como proceder o item 11? do arquivo pdf ms parameter window? pa

Juki / Zevatech 730/740 - MS Parameters window

Aug 17, 2018 | A lot of machines have such parameters stored in an ascii file that can be edited with notepad. But

Juki / Zevatech 730/740 - MS Parameters window

Aug 16, 2018 | Hello! Does anybody know how to access the "MS Parameters" window on older JUKI Pick and place mach

K&S 4524A Wire Bonder

Jul 26, 2017 |

printing problem on mydata machines

Jan 26, 2017 | If you're lucky, that parameter can be unlocked using the parameters password. If you're unlucky,

printing problem on mydata machines

Jan 24, 2017 | we have one dot matrix printer and i would like to connect it to the TP9 machine. The parameters se

DRY SOLDER ISSUE

Jun 22, 2016 |

Assembly Quote

Nov 26, 2015 |

Universal GSM 2

Oct 13, 2014 | parameters -> axis that z axis for head2 is also enabled ("axis mounted" must be 1)

GSM 2 image not appearing on cameras

Mar 9, 2013 | Machine -> Configuration -> Parameters -> Setup then go to vision setup page, if available. - Dej

Puzzling CSM84VZ errors, #118 and #120

Nov 1, 2011 | Hi , I would think that when you added the new parts, you missed to give them some of the parameter

PathMaster Program

Oct 27, 2011 | What sort of coating are you trying to spray? The parameters are going to be drastically different

BGA solder bridge

Mar 21, 2011 |

Reject Rate

Nov 16, 2009 | for reject rate depends on various parameters, Part data parameters, (Body tolerance,Part pickup &

SPC control-Wave soldering

Aug 2, 2009 | Hi all, If we are using non clean flux, what are the wave soldering parameters that we should mon

Flux residue

Jul 28, 2009 |

No-clean, water-based flux residues after wave...

Feb 3, 2009 | Hi George, I would suggest you to re-look your process parameters, especially for the pre-heat tempe

AOI false fail PPM

Jul 29, 2008 | 330 000ppm on low volume. what is the parameter you are talking about? PPM on AOI?

Bridging Problems

Mar 17, 2008 | Hi SWAG, Bridging most contributed is from printing set up which is the parameter setting as well

Mydata A12 tool tip damage

Jul 19, 2007 | Peter, GO TEST YOUR SMALL X-MOTOR IN THE SERVICE PROGRAM !!!!!! Do not start changing paramete

Pin Through Paste w/ No-Lead

Apr 2, 2007 | The parameters are the same as leaded paste. The results are slightly worse.

Component Specifications

Feb 28, 2007 |

DEK pro-flow

Feb 16, 2007 | We conducted a DOE to establish our print setup parameters. These will of course depend on the past

Lead Free paste

Nov 8, 2006 |

Vectra Question

Aug 7, 2006 | You cannot configure or change this parameter. I would suspect your ultra sonic sensor at the begin

Edge Clearance

May 3, 2006 | IPC or DFM? Most DFMs are controlled by the equipment restrictions which will define this parameter

SPC for Wave solder (defects on PCB's)

Feb 7, 2006 | Cal is right. SPC doesn't work at wave, period. Establishing parameters is very key for each produ

Flexible pick & Place

Facility Closure