Electronics Forum: plating (Page 146 of 252)

imm. silver

Electronics Forum | Thu Aug 29 17:51:43 EDT 2002 | nifhail

I have seen several Imm Ag pad on the assembled board which have a copper colorleaching through the silver plating This happened on the pad which was not deposited with paste during the assembly process. Don't know if it is a problem, but we only h

About the PCB gold finger contamination.

Electronics Forum | Thu Sep 19 17:14:02 EDT 2002 | davef

Comments are: * Use an eraser if the surface of Au is not clean, but make sure the eraser has no/low ionics (such as sulfur that is a common additive for rubber). * If the plating surface required eraser to remove the top surface, the plasma normally

Gold plated board, with csp's and 0603 with no clean apetures

Electronics Forum | Thu Sep 26 14:43:43 EDT 2002 | Jim M.

unsure of what solder spec. your working to?.IPC/EIA J-STD-001C, Section 9.2.4 clearly states dull, matte, gray or grainy appearing solders are accpetable depending on your process and if the acceptability of the neaxt paragraph is met.IPC 610 and J-

Gold plated board, with csp's and 0603 with no clean apetures

Electronics Forum | Wed Oct 02 18:18:58 EDT 2002 | davef

The steadfast rule of thumb is: In order to get reliable reflow, you need to be at or higher than [liquidus + 20�C] for about 5 to 10 seconds, rather than those old "60 seconds above 183�C" guideline. This provides for setting your peak based on the

Cracked vias

Electronics Forum | Mon Dec 16 10:54:48 EST 2002 | davef

Knee of barrel and pad crack: Caused by thermal stress during soldering, because epoxy expands in the "z" 3X more than "x" or "y" which are restricted by the fiber. Related to: * Design of pads too large relative to hole diameter * Temperature at o

0402 stencil design

Electronics Forum | Tue Feb 04 09:03:45 EST 2003 | Russ Roberts

Greetings, I am pretty new to SMT production, and have learned much from this forum. I am getting ready to build a CCA with many 0402 parts that are really close together. I consider these fine pitch. The board also has two QFPS, so my stencil design

Plated through via's in pads.

Electronics Forum | Wed Feb 05 21:05:38 EST 2003 | davef

Iman On your situation: As an earlier poster stated, your options are limited to opening you stencil aperture to compensate for the paste lost to the via. On your designer's belief that "it helps in heat dissipation": Could be true, but: * Hole wil

Black pad defect

Electronics Forum | Wed Feb 12 17:41:18 EST 2003 | MA/NY DDave

Hi, Gee David F is as bad or as good as me on a bad day. Boy can I get mad... "new information" Many of these defects have been around so dang long and seem to get recycled as the latest rage and the newest of new information in technical articles

removing solder from a 0.015" hole

Electronics Forum | Wed Feb 26 18:48:01 EST 2003 | kennyg

I'm trying to solder a 0.011" lead into a 0.015" +/-0.003" hole. Stop laughing please. This is normally possible with difficulty, except if the lead is removed and the attempt is made to re-install a lead. Anyone have thoughts on how to remove nea

Plating for aluminum wire bonding

Electronics Forum | Sun Mar 02 17:40:02 EST 2003 | MA/NY DDave

Hi It sounds like you are in a different country or in the USA a long time ago. I have no idea of the process either is using, so they can be comparable or one can be better than another and lop sided compared to other places. Benchmarking I think


plating searches for Companies, Equipment, Machines, Suppliers & Information